appleseed
Active Member
This is how I built my bag type vaporizer.
I used:
A digital heat gun
a vaporizer whip (ebay $10)
an aluminum funnel (3" I think. Maybe 4")
a size 10 1/2 knitting needle
a straw and cap from a sports bottle
an "O" ring the size of the front of the heat gun (3" on mine, I think)
scissors
electrical tape
screwdriver
something to cut the funnel (hacksaw blade? sheet metal shears? I used an open
shoe grinder...)
This is very simple really. Cut your funnel to where the area left over is
larger than the mouth of the heat gun and leave 3 or 4 legs. Push this down
snug on your heat gun and clamp it with the "O" ring (hose clamp). Then cut
off the end of the whip away from the bowl. About 10" or 12" and tape the
mouth of the oven bag around half way on the short piece. Cut the knitting
needle about 3" or 4". Cut the tip off. This gives you a hollow tube. Push the
blunt end about 1/2" into the hose with the bag. This will be your coupler to
the bowl. Push on, pull off. Cut a 1"or 2" piece from the straw with cap and
slide it on the knitting needle when the bag is full to make a cap. (not all
straws fit...) Done. Set the gun for your favorite vape temp, preheat a minute
or so, push whip bowl (filled) onto funnel with slight twist and it grabs then
the bag fills with vapor. I've been using mine for a couple weeks now and find
it very easy to use. I was afraid I'd need clamps or something to hold the
bowl on but the air flow that comes out of my heat gun is not that high on
low. Take a look at the pics. They show it step by step enough to where you
probably don't need my desciption. Funnels may be different on the end. Try
your whip bowl for fit before buying.... I spent under $50 including the heat
gun and this works as well as anything I have ever used.
I used:
A digital heat gun
a vaporizer whip (ebay $10)
an aluminum funnel (3" I think. Maybe 4")
a size 10 1/2 knitting needle
a straw and cap from a sports bottle
an "O" ring the size of the front of the heat gun (3" on mine, I think)
scissors
electrical tape
screwdriver
something to cut the funnel (hacksaw blade? sheet metal shears? I used an open
shoe grinder...)
This is very simple really. Cut your funnel to where the area left over is
larger than the mouth of the heat gun and leave 3 or 4 legs. Push this down
snug on your heat gun and clamp it with the "O" ring (hose clamp). Then cut
off the end of the whip away from the bowl. About 10" or 12" and tape the
mouth of the oven bag around half way on the short piece. Cut the knitting
needle about 3" or 4". Cut the tip off. This gives you a hollow tube. Push the
blunt end about 1/2" into the hose with the bag. This will be your coupler to
the bowl. Push on, pull off. Cut a 1"or 2" piece from the straw with cap and
slide it on the knitting needle when the bag is full to make a cap. (not all
straws fit...) Done. Set the gun for your favorite vape temp, preheat a minute
or so, push whip bowl (filled) onto funnel with slight twist and it grabs then
the bag fills with vapor. I've been using mine for a couple weeks now and find
it very easy to use. I was afraid I'd need clamps or something to hold the
bowl on but the air flow that comes out of my heat gun is not that high on
low. Take a look at the pics. They show it step by step enough to where you
probably don't need my desciption. Funnels may be different on the end. Try
your whip bowl for fit before buying.... I spent under $50 including the heat
gun and this works as well as anything I have ever used.
