Homemade smoking devices

mc.eddy.supreme

Well-Known Member
how did u make a blunt out of an , here are the directions for an pipe if u need it

Pipe

Everything is good about the pipe. They're cheap (under a dollar for a couple at the store), easy to make, smokes VERY WELL along with a cool, smooth, y taste (yup!), and they conserve weed because you are forced to pack little bowls rather then a joint.

Items needed:

--An . I prefer a nicely shaped that can stand up on its own without falling over. That?s unless you like holes burnt in your carpet.

-- A pen...best is the cheap Bic ones. Any pen is fine just as long as it doesn?t have a pocket-clip-thing. If there is no pen around, you can use anything that?s shaped like one, just as long as the sides are parallel.

-- If you don?t use a pen with the ink thing on the inside you will need a nail or something of that size.

Step1:
The trickiest part about making the pipe is pulling off the stem on top. The trick is to pull out the entire stem. Do this by gripping it as close to the base of the stem as possible. You DONT want to rip half the stem off, or your pipe is already ruined. Its not hard, just give it a twist before/while you are pulling.

Step2:
Use the pen to penetrate a hole HORIZONTALLY ALL THE WAY THROUGH the middle of the . Make sure it lines up with the hole on top where the stem was.

Pull out the pen and then penetrate the again with the opposite side of the pen...this will push out all the gunk in the middle of the . What I do after is blow out any seeds or extra crap inside the (you dont wanna be smoking seeds, or choking on them).

Step3:
Take out the inside of the pen, the ink cartridge. Use that smaller diameter cartridge to poke another hole, this time VERTICALLY, HALF WAY THROUGH the . This is your toke hole.

Push down until it meets up with the horizontal fat hole. Its real important to make sure you DON?T make a fat hole or your weed will suck through when your are . After that, once again, I blow out any extra gunk....Its all really important to make sure all the holes are nice n clean so the airflow between them are not clogged up....You don?t want a pipe that takes all your strength just to pull in some smoke.

BOOM! theres your pipe. Put your marijuana in the bowl on top. Use one hole as a clearhole/carb and suck from the other. The pipe will last a whole day until its starts to go brown n rot. Best thing about the pipe is YOU CAN EAT THE EVIDENCE!
 

mogie

Well-Known Member
You guys have been awesome the list is getting huge. Check it out and see if your invention is there. GrowFAQ, DIY and save, click on page 2 (it's that long we needed a second page!)
 

azkule

Active Member
I just put this beast together, hits like a champ
its a 1 litre bottle.
Sealed the stem opening with almost half a candle's worth of wax then some crap school glue (cooled with hair dryer) then put a cardboard ring around + tape for protection.

the slide is so you can easily dump and clean the bowl EVEN if you wasted, just as long as you dont dump the bong over.

the card is a little small for my likings but it works.


sorry the pictures are so big, had to use a digital camera because my webcam busted.


Whole Bong



Slide and Stem Housing



Slide (tape so it fits snuggly in the stem)




Carb, just because i can

 

Hetfield82

Active Member
Alright...I have a home made smoking device, I'm willing to fork it over, or get a photo of it, but i cant explain it, its way to complicated, but it hits like a champ, so what do you say people...?
 

The Ganjanator

Active Member
Materials
* 1 POM Pomegranate Juice drink(walmart,kroger,etc.)
* Razor or knife
* a bong slider and glide w/ rubber o-rings
* water(optional)

Procedure
Step 1: Drink POM and wash thoroughly with soap and hot water.
Step 2: Cut perfectly sized hole in side of bottom-most 'bubble' of bottle for the glide to
fit.
Step 3: Insert rubber o-ring to fit hole for slider glide, then fit glide into the new opening
Step 4: Fill above glide with water and insert slider and bake through the top. Enjoy!
 

Attachments

The Ganjanator

Active Member
Materials
* One 7 inch piece of 2 inch diameter PVC piping
* One 2 inch diameter PVC piping endcap
* Knife or drill w/ 1/8 inch bit

Procedure
Step 1: Seal endcap to piece of PVC, then clean with hot water,
Step 2: Cut or drill joint-sized hole into center of endcap.
Step 3: Then cut or drill tiny hole near the open end for carbeurator.
Step 4: Roll one up and fit it into the hole snug, hold carb, light and toke up!
 

Attachments

The Ganjanator

Active Member
Materials
* 2-3 same sized pill bottles
* Hot Glue Gun
* Bendy straws
* Knife
* Scissors
* a bowl n stem (preferrably metal)

Procedure
Step 1: Cut straw-sized holes into bottom-center of 2 pill bottles.
Step 2: Insert longer end of bendy straw in through the open end of each of the 2
bottles down through the holes in the bottoms. (must look like upside down U
inside bottle) Seal with hot glue and clip off excess straw from bottom.
Step 3: Fill the 2 'percolating' bottles halfway with water and fit bottom of one into the
top of the other tightly.
Step 4: Cut hole into bottom-center of last bottle and fit bottom of bottle into top of the
other 2 bottles.
Step 4: Cut hole into side of bottom-most bottle and fit stem and bowl in and seal.
Step 5: Cut tiny hole into side of top-most bottle for carbeurator.
Step 6: Let sit... pack bowl, light and toke!!!!
 

Attachments

The Ganjanator

Active Member
Materials:
* a Thermos that can fit almost a whole 2 liter( go find one somewhere...)
* an empty 2 liter( stripped of labels)
* Knife
* Glass slider w/ rubber o-ring

Procedure
Step 1: Clean Thermos and 2 liter and strip labels off.
Step 2: Cut bottom off of 2 liter.
Step 3: Cut hole into cap just big enough to fit stem of glass slider into.
Step 4: Pack bowl, keep lit and pull up, take cap off when ready and push down inhaling. boooooonnnnngggggg........
 

Attachments

Top