Been growing for about two years now. Just started co2 recently, I understand that my temps need to be 82 to 85ish to take the most advantage of co2 enrichment. Is that room temps or canopy temps? Currently running 79 degrees in room humidity around 58 percent, canopy at 84-85 humidity much lower of course. According to the pulse vpd chart im good for room vpd and very poor considering canopy. Plants are looking very healthy, but im afraid im missing out on potential, or wasting CO2. Can someone please help?
Co2 and vpd?
- Thread starter mhalter81
- Start date
BobThe420Builder
Well-Known Member
Never used c02, never an issues
Sealed room they say can benefit, but I see no need for it
Sealed room they say can benefit, but I see no need for it
BobThe420Builder
Well-Known Member
I'd say work on your grow knowledge and process to increase production
Fernvalley
Member
I run my canopy at around 83-84 and humidity between 50-60. If you're locked in at growing without supplemental co2, you'll see a big benefit to growth rate and yield.
When I started using co2, I increased my yields by 60%...BUT HOLD ON. I was growing is a sealed room with a ton of biomass growing. I picked up a co2 controller before I got a tank and placed it in the room. I noticed that each day I was dropping below 250ppm at many points. So really I was correcting a problem that I didn't know I had.
But I will never grow without it again.
When I started using co2, I increased my yields by 60%...BUT HOLD ON. I was growing is a sealed room with a ton of biomass growing. I picked up a co2 controller before I got a tank and placed it in the room. I noticed that each day I was dropping below 250ppm at many points. So really I was correcting a problem that I didn't know I had.
But I will never grow without it again.
BobThe420Builder
Well-Known Member
Pretty hard to believe unless you really sucked at growing prior to adding c02...lol
You are correct, everyone should do this. Thats why I asked the question. Without co2 my plants were healthy throughout grow, I would average anywhere from .85 to 1 gram per watt cured. I try to strive for perfection. Again, if I can get more yield, denser buds with CO2 at same cost why not try and achieve that. Btw, I get Co2 for free.
Fernvalley
Member
Great response. And from someone that has no experience using supplemental co2.
Not saying I was the best grower on earth...but I had a ton of foliage for the cubic footage of my grow space. The plants were very healthy...just slow growing and modest yield. They consumed the ambient co2 at a high rate causing the levels to bottom out. And at this point they stall.
Just sharing my personal experience.
Thanks for your relative input for the question asked above.
pahval
Well-Known Member
hey mate, i hope i can help, i just posted about this somewhere else on this forum, ill post my resources again:
[...] well, you have to measure temperature of air around the plants (so in canopy level, it wont help much if you measure temps around your lamp), AND you have to measure your leaves temps, i would suggest handheld IR thermometer for that, because we are measuring difference of air vapor saturation and leaf vapor saturation, and that is the vapor pressure deficit we want to have so that our plants can transpire as much as they can without any stress... a good chart, which takes into account your leaf temp (but it looks ugly), can be found here:
a good info about vpd i have found here:
and good info about temps and other with using co2 i have found here:
overgrow.com
especially pdf from fluence, which has recommended temperatures with and without co2 supplementation...
[...] well, you have to measure temperature of air around the plants (so in canopy level, it wont help much if you measure temps around your lamp), AND you have to measure your leaves temps, i would suggest handheld IR thermometer for that, because we are measuring difference of air vapor saturation and leaf vapor saturation, and that is the vapor pressure deficit we want to have so that our plants can transpire as much as they can without any stress... a good chart, which takes into account your leaf temp (but it looks ugly), can be found here:
a good info about vpd i have found here:
and good info about temps and other with using co2 i have found here:
Factors that influence growth and development ( Temp and VPD)
I’ve uploaded the Fluence guide before, here’s the complete version Fluence Bioengineering_High PPFD Cultivation Guide_v1.2.pdf (1.4 MB) another good one! Lumigrow LumiGrow_LED_Growers_Guide_for_Cannabis.pdf (2.0 MB) and not to be outdone…Illumitex…we got 'em all here at OG...
overgrow.com
especially pdf from fluence, which has recommended temperatures with and without co2 supplementation...
Thank you so much, the plethora of information that you have given me this day, is very much appreciated. I have quickly skimmed through all of it, and plan on referring back to it over the next several days. Even though I was very unsure of myself attempting what I'd consider next level grow methods, I am within close range of optimal cultivation. I honestly believe this info will help me succeed at the next level. Again, thank you so much!hey mate, i hope i can help, i just posted about this somewhere else on this forum, ill post my resources again:
[...] well, you have to measure temperature of air around the plants (so in canopy level, it wont help much if you measure temps around your lamp), AND you have to measure your leaves temps, i would suggest handheld IR thermometer for that, because we are measuring difference of air vapor saturation and leaf vapor saturation, and that is the vapor pressure deficit we want to have so that our plants can transpire as much as they can without any stress... a good chart, which takes into account your leaf temp (but it looks ugly), can be found here:
a good info about vpd i have found here:
and good info about temps and other with using co2 i have found here:
Factors that influence growth and development ( Temp and VPD)
I’ve uploaded the Fluence guide before, here’s the complete version Fluence Bioengineering_High PPFD Cultivation Guide_v1.2.pdf (1.4 MB) another good one! Lumigrow LumiGrow_LED_Growers_Guide_for_Cannabis.pdf (2.0 MB) and not to be outdone…Illumitex…we got 'em all here at OG...
especially pdf from fluence, which has recommended temperatures with and without co2 supplementation...
J232
Well-Known Member
You would want to adjust the air temp to reach a desired leaf temp. I skimmed threw and didn’t see your lighting, that will factor in there too. If you are new to co2, as I am, I would grab a IR thermometer. I have no problems growing without, I didn’t want to exhaust my room outdoors in winter as it would look like a power plant stack in my mind. I can only assume the free co2 is food grade as well.
pahval
Well-Known Member
yep, thats also a thing, co2 must be food grade... if you go with co2, you need more of lights and nutes... also, if you go with higher VPD that will mean plant will absorb more water, hence will absorb more nutrients, so be careful about it, maybe you just need to raise vpd (make plant intake more), or you keep same vpd as before co2 and enrich your nutrient solution more... anyway, im glad to help out! <3
I attached several pics( don't mind the clutter, cleaning up veg room at the moment). Again everything seems to be healthy, two more days will be the beginning of 4th week of flower. The lower temp/ higher rh is room air, the higher temp/ lower rate is at canopy level. My current leaf temp is anywhere from 76 to 79 degrees. I am running 24 hlg 132qb's @ 1400ma12 hrs a day (par is at its highest 1136umole and 697 at the very far corners) and 4 super b uvb bulbs 3.5 hours a day(also something new for me). 4x8 room, plants veg for approx 6 weeks. Vpd is hard for me to wrap my head around, mostly because all of the resources that I own say to keep humidity levels much lower than what vpd charts claim. Anyway, thanks again to everyone that has helped thus far. Before anyone says anything I know I have a lot of wasted space. Lol
Attachments
pahval
Well-Known Member
They look nice... Lower rh recommendation is to prevent having bud mold, but from what ive seen these people also have high temps, mold comes with high temp and hum, ive red somewhere tha user had high temp and hum trough the day and lower (esp. humidity) trough the night and had no problems... And in the end, if it works for you, just follow that, you can experiment on some smaller grow...
TintEastwood
Well-Known Member
Good info here...
manicbotanix.com
The above has helped me become a better grower. Co2 supplemented or not.
I keep room in the 80s. W leds/cmh
Leaf surface temps in the low 80s.
Rh 50 avg. no higher than 60.
That's with Co2, between 600ppm in veg, up to 900 max. in flower.
Site permanently closed due to piracy and trading off Issues
Site permanently closed due to piracy and trading off Issues. Manic Botanix, nor its author, is in no way linked to any commercial interests claiming a link. Full stop. The domain and its content are now for sale. No low ballers need apply. Contact [email protected]
manicbotanix.com
The above has helped me become a better grower. Co2 supplemented or not.
I keep room in the 80s. W leds/cmh
Leaf surface temps in the low 80s.
Rh 50 avg. no higher than 60.
That's with Co2, between 600ppm in veg, up to 900 max. in flower.
NukaKola
Well-Known Member
Dig the QB 132's! How are you liking the Autopilot APC8200? Was thinking about picking one up.
Thanks. Autopilot has worked well so far. I dont care for the lights on it, but hasn't seemed to cause any problems yet.
insomnia65
Well-Known Member
The guy on that video could do with breathing only CO2 for a a while grr.hey mate, i hope i can help, i just posted about this somewhere else on this forum, ill post my resources again:
[...] well, you have to measure temperature of air around the plants (so in canopy level, it wont help much if you measure temps around your lamp), AND you have to measure your leaves temps, i would suggest handheld IR thermometer for that, because we are measuring difference of air vapor saturation and leaf vapor saturation, and that is the vapor pressure deficit we want to have so that our plants can transpire as much as they can without any stress... a good chart, which takes into account your leaf temp (but it looks ugly), can be found here:
a good info about vpd i have found here:
and good info about temps and other with using co2 i have found here:
Factors that influence growth and development ( Temp and VPD)
I’ve uploaded the Fluence guide before, here’s the complete version Fluence Bioengineering_High PPFD Cultivation Guide_v1.2.pdf (1.4 MB) another good one! Lumigrow LumiGrow_LED_Growers_Guide_for_Cannabis.pdf (2.0 MB) and not to be outdone…Illumitex…we got 'em all here at OG...
especially pdf from fluence, which has recommended temperatures with and without co2 supplementation...
Renfro
Well-Known Member
One thing about CO2 enrichment, the plants actually perform better if you have low points and high points. I wish that I could set a larger dead band on my CO2 controller personally but I can use periodic vent cycles on a timer to achieve the same thing.