New grower little knowledge help please!

I have brought this grow set up, i copied the full specs and descriptions.

I have got the 600W version and a 4 pot DWC system.

Problem is i only have one single socket in the place id like to put the set up listed below + the DWC system.

I gather i cannot run this all off one single socket with a good extension cable with a breaker? Or can i? Can anyone help me solve this issue and direct me on how to set this up safely electrically, in terms of the set up i know how but the electrics i have no knowledge on, id even pay people for advice due to wanting to get my first grow set up safely dont want any fire or heat.

oCo 600w Kit
In this kit you will get the following item:

Ballast 600w ---- 600w Bulb Dual Spectrum ---- ReflectorTent - 0.8m2Swiftair Inline fan kit - Centrifugal fan, Carbon Filter, Alu Ducting, Clamps Canna CoCo Natural 50 litreCanna A+B 1 LitreFabric Pots 11 litre x 2Yo Yo Hanger (Pair) - Please selectTimer - Please select

Please see below for description on products:
The 250w Ballast, has been designed for improved quality and high output,
✓ Metal Case
✓ Fitted with IEC connector cord and UK mains lead
This produces the full light spectrum with added blue for the propagation and vegging stages. We recommend you replace lamps every 3-6 months to avoid diminishing harvests.
Lamp size and output
600 watt - 90,000 Lumens
Please keep the retail packaging in case you need to return it to us. Bulbs sent without the original packaging are not covered by warrant
SUPERB VALUE HYDROPONIC TENT
Quality Hydroponic Grow Room Tents
95 % reflective hammered silver lining
Heavy duty zips
Metal poles (please make sure these a pushed all the way in on the side clip provided)
5 x 150mm Air holes (2 Left, 2 Right & 1 on Top)
1 x 80mm hole
Passive ventilation windows: 2
(we found the easiest way to put up is fix bottom half first then top part and start from the back)
PowerPlant Heavy Duty Timer - Please select if needed
Normal household timers are not built to take the high inductive loads produced by HID ballasts. If used with an HID ballast - the contacts inside the timer that open and close the timed circuit will overheat and weld together - breaking the timer and leaving your grow lights permanently on.
The PowerPlant Heavy Duty Timer is different. It is designed to take high loads and has no problem dealing with the inductive loads produced by a 600w ballast.
This means no separate contactor is required and saves you money. It has a 96 switching operations within a 24 hour period (every 15 minues).
This timer is suitable for timing one 600w HID ballast. It has a robust case design with socket and timer dust/moisture covers.
This unit is ideal for timing 400w and 600w ballasts. Do not use more than one 600w ballast per timer.
Fan Kit
FAN, ALUMINIUM DUCTING, CARBON FILTER, CLAMPS X 3
Air Flow
Centrifugal fan - 110 m3/h - comes with stand attached to screw to floor (can not see in picture)
Carbon Filter Size
To get the most out of your kit, please follow these few tips:
Remember, if you reverse-mount your Filter you will lose the benefit of your pre-filter and reduce the life of the carbon.
Always mount your filter as high as possible. Hot air naturally rises and so will your odours!
Try not to block too much of the filter with mounting straps or hanging devices. Use the ends of the filter to support, so not to inhibit the surface area of the filter.
Do Not mount your Filter near to humidifiers. Humid air over 85% may enter the filter rendering the activated carbon ineffective and your filter may NOT neutralise odours!
Ensure you have an airtight seal around the connection of your filter to ducting or extractor fan.
On delivery:
The carbon filter can some times have carbon dust come through to the white outer casing making it blackish or grey this is not a issue and fine to use as long as the carbon f

Use a power strip, like you would for a computer.

Si this dytem could run in a single socket in a wall safely in my bedroom? It wouldnt overpower my outlet?

If you are worried split the circuits up run half off one circuit and the other half on another. I only have 110 in my place and I run a ton of equipment of 2 circuits. Manufactureers have to cover their asses is all, just dont run it off a circut that say runs the ac unit or anything else high in amps. I run my lights at night when the heat and most lights in a house are on, but my house stays really dark except for the rooms we are in so it evens my light bill out and keeps my girls from being cold during the nights.
Moondance

So i only have access to the single, any advice?

I did not read your whole book...but in the simplist of terms...

Add up the total wattage of all your components and diviide by 100 and compare that to the amperage of your circuit breaker. (This is not exactly how you would come up with the perfect values but this gives you some padding) If your total is less you are good to go with a power strip.

You will be fine using a power strip plugged into a single wall outlet. Most gamer desktop computers have 600-800watt power supplies, if those are fine on a single outlet (as they all are), your setup will be fine. If it's too much, the breaker will trip.

Lovely thankyou guys any links where i can buy a good safe power extension