What did you accomplish today?

manfredo

Well-Known Member
Looking at some of these also.
This one has 2 separate probes that can be programmed separately, heat or cool or both.
Inkbird can only do 1heat/ 2cool but has pump delay for AC/etc.
Both are 10 amp,
https://www.amazon.com/dp/B0811KPFVN/?coliid=I3SCOKBM4ZAQLA&colid=2NMXDG6DUE4VL&psc=1&ref_=lv_ov_lig_dp_it

This WILLHI WH-1803C is a nice unit for keeping something an exact temp , compensating for thermal lag automatically.
It's an actual PID Digital Temperature Controller, but Heating only at 5A.
Nice for sous vide, seed mats but not a big power draw like an exhaust fan.

https://www.amazon.com/WILLHI-Temperature-Controller-Thermostat-Fermentation/dp/B07MCH4S73/ref=sr_1_7?dchild=1&keywords=WILLHI&qid=1596378875&sr=8-7

I got one of these Digiten units because it has a waterproof stainless probe, which the inkbird does not unless you get the "S" unit with the shorter plastic detachable probe.
The Digiten has a standard probe you can replace with other mfgr, inkbird says no!
I think you can get an even longer stainless probe direct from Digiten.
https://www.amazon.com/DIGITEN-Thermostat-Pre-Wired-Temperature-Controller/dp/B071SDVLBG/ref=sr_1_8?dchild=1&keywords=DIGITEN&qid=1596379467&sr=8-8
Thanks for the ideas/input!! Decisions, decisions! The reviews are a little sketchy on all these Chinese controls, but it's got to be better than freezing gallon water jugs to keep the res cool like my last grow. I think the mini fridge setup will work well!!
Going to go dust off the nutriculture and replace some nozzles, maybe get it set up.
 

DCcan

Well-Known Member
These are Digiten Single Stage controllers, but rated at 15 amps.
They can cool or heat, but only 1 outlet with high wattage, not many others with 15A, another good unit.
https://www.amazon.com/gp/product/B07BFR1Z4B/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
Thanks for the ideas/input!! Decisions, decisions! The reviews are a little sketchy on all these Chinese controls, but it's got to be better than freezing gallon water jugs to keep the res cool like my last grow. I think the mini fridge setup will work well!!
I did the same thing, looking for a controller with flexibility for other projects, non proprietary parts, pre wired cause I don't need a hobby, got one.
 
Last edited:

DCcan

Well-Known Member
I lost 20 because I was stoned and drinking rum and decided "somethingsomething" was an awesome new password.
No more password changes after sundown was a new commandment.
Got my own commandments, much better way to do it.
1) Don't fuck with me.
2) What, who, me? Nope, can't recall.
 

raratt

Well-Known Member
Last light is tacked into the ceiling, found a couple wires I have no idea why they ran them where they did. I did NOT find them with the sabre saw at least, missed them by a couple inches. I think they are 220 lines running to the dryer and AC. I installed one of the lights permanently that is adjusted to the color we want. The middle one is where the switch feed goes in and the other 2 have to be wired to that one. There are push on Wago connectors in there, but not enough slots to put all the wires into so I have to cut them off and use wire nuts, not enough room for both of them.
I'll finish up the wiring and light temp adjustments tomorrow.
Bacon cheeseburgers for dinner, buds and suds in a moment.
 

cannabineer

Ursus marijanus
Last night in the hot gale (90 degrees at 1am) a fence panel blew out. I was out there at sunup driving nails and screws into whatever purchase I could find in the spongy ancient wood of the fence. I went to open the gate from the outside, have to reach over the top to get the latch, and felt a little sting.

I walked through the house to inspect the inside of the fence and found this nest. Much death spraying ensued. Good fucking morning RIU.

C62B365A-D482-4CCE-B1D1-96B138DD37B5.jpeg
 
>
Top