Harvest a Pound Every Three Weeks!

DragonPhoenix

Well-Known Member
Hi Stink -

I just thought of this and was wondering if you could provide some of your thoughts...

I'm using the system you've shared with us here and I've got alot of plants started from seed. I have some White Widow clones but I have alot of different genetics started from seed. I want to clone this for the other grows however this is what I thought of.

If starting from seed and taking a clone, you want to wait for preflowers to form because every clone is the same age as it's parent.
This means I'll have to have some plants in the veg unit for up to 6 or more weeks. I can't imagine having plants in the unit for that long - they would be TOO huge. So...what do you think I should do? Just top them or trim them back until they show preflowers and after the first clone I would be fine (because all clones taken would share the same age as the first clone)...I'm probably sounded retarded now but I hope I made that clear enough that you can figure out babble-speak.
 

oneeyejedi

Active Member
stink
i am buliding one of you ststems and i have a friend who builds LED he is going to trade me a 600w if i build him one too. any luck with led? i have not heard very good results yet but have not actually seen results either. also i have seen cfl's being used to flower. My gutt tells me to stick with what i know and go with the growzilla as before with 1000w hps and 1000w mh. what do you think
 

havefungodumb

Well-Known Member
i have timers, do you need a certain 1?.

thanks for replys boys.

not to bad, im gonan start a thread to show some stuff i have, check it out ima try right now.
 

SVINIAR

Active Member
Yep, search "hydro recycle timer" on google, you'll see what you need.

Also whatever happened with this timer?

http://www.marinedepot.com/ps_ViewItem~category~Aquarium_Systems_Natural_Wave_Wavemaker_Saltwater_Aquarium_Supplies_Wavemakers_External~vendor~ASI_or_Aquarium_Systems~SearchStr~~action~view~idProduct~AS4111~idCategory~FIWMEW.html

Only thing i can find about it is this..
"Natural Wave™ has 3 outlets with adjustable frequency(time) – change duration of cycles from 20 seconds to 3 minutes"
and this..
"very simple to setup and configure. Just turn one dial (adjust time between power heads being turned on) and you’re done"

Now this all sounds good, but dont we need 2 settings, on and off, or am I missing something here with how this thing works?
Because $45 is better than $65/$85 any day of the week.
 

DIRTHAWKER

Well-Known Member
Hey stink, do you glue the caps on the fence post? i was thinking of maybe duct tapping them really good, so after each harvest it would be easier to clean. what do you think?
 

StinkBud

Well-Known Member
could you do me a favor and talk a little bit about the battery back up that you use?
I use one of those cheap APS models that you can get from Wallies. If I was going somewhere for a while I would buy a bigger one. Right now I don't use anything because power is safe. But as soon as the big storms come I'll plug it in. I also have 1000W Honda generator and a 2800W gen in my van if I need it.

Also I realize this may be strain dependent to a degree and that you have to keep your plants under 12" due to state law but how big are your plants generally when you put them into flower?
I keep them under 12" due to a number of reason. The main reason is do to the State Law requirements.

But there are other reason also. Topping them causes more side shoots. These are the shoots that I use for cuttings

Now look at this photo. I had to tie the Skunks down at 1.5 weeks! The Elvy is in the lights after three weeks.

You could veg them longer but they would get so tall that the light would never reach the bottom leaves.

I'm assuming you take clones right before you put them into flower unit, correct?
Yes, but I also take them from the new flowering plants for up to a week.

I've even taken clones from flowering plants. I have two Skunk clones that are in my cloner now with full buds. I thought I had talen a cutting of that specific phenotype but realized later that I didn't. Of course it ended up the being the pheno I was looking for:roll:. No big deal, the cuttings will regenerate and be fine.
 

Attachments

StinkBud

Well-Known Member
SB great post have been thinking of this kind of set up for a year and has been too afraid. any way you have convinced me I hope I can do it 3/4 as good as you.

One Question: In the flower setup do you put the sprayers directly under each pot?
If so, would it be better /or worse to have a sprayer on each side of net cups?

This thread is helping a ton of people keep up the good work
Sprayers are between each net pot. Just like in the plans...
 

StinkBud

Well-Known Member
Hi Stink -

I just thought of this and was wondering if you could provide some of your thoughts...

I'm using the system you've shared with us here and I've got alot of plants started from seed. I have some White Widow clones but I have alot of different genetics started from seed. I want to clone this for the other grows however this is what I thought of.

If starting from seed and taking a clone, you want to wait for preflowers to form because every clone is the same age as it's parent.
This means I'll have to have some plants in the veg unit for up to 6 or more weeks. I can't imagine having plants in the unit for that long - they would be TOO huge. So...what do you think I should do? Just top them or trim them back until they show preflowers and after the first clone I would be fine (because all clones taken would share the same age as the first clone)...I'm probably sounded retarded now but I hope I made that clear enough that you can figure out babble-speak.
Sounds to me like you will be harvesting a lot more than a pound that harvest! Don't worry, just tie the tops down. I use those little bread tie types you can buy at the grow shop.

I tie the shit out of my big plants. It causes all the side branches to become huge! That is exactly what happened to me this harvest. I haven't trimmed it yet but it looks to be about 1.2-1.4LBs this time. I'm dreading having to trim all this bud. It's fun the first year but after 14+ years it's getting to be a real pain in the ass.:roll:
 

StinkBud

Well-Known Member
Hey stink, do you glue the caps on the fence post? i was thinking of maybe duct tapping them really good, so after each harvest it would be easier to clean. what do you think?
Use silicone and lots of it! I run two beads along the inside of the cap and then put it on. Then I run another bead along the outside and smooth it out with my finger.

Tape WILL leak. Fuck, even the silicone will leak if you don't do it right the first time. Don't ask me how I know this:mrgreen:.

You guys are lucky! You get to learn from all my mistakes...
 

StinkBud

Well-Known Member
With the size of this thread I can imagine how hard it is to find the tutorials and plans. So I though I would put it all together in one post for you.

Here you go!

Harvest a Pound Every Three Weeks
By StinkBud version 1.1


Outdoor growers are heading inside now so I thought if might be a good time to start a tutorial on how you can harvest a pound every three weeks from a 7x8' closet.

I'll take you through my process from start to harvest.

What is different about my system vs. others?

1) 3 separate Aero/NFT flower systems allow me to run a 9 week flower cycle. This allows the buds to fully ripen and also allows me to run strains with more Sativa in them.

2) I use 100% organic nutrients for the sweetest tasting bud you can ever imagine.

3) I take my cutting from my vegative plants. This way I can run 10 different strains without having to keep 10 mother plants.

4) My system is all Aeroponic/Hydroponic or Aero/NFT. Each system uses the same sprayers and pumps. No medium is used. Basically the plants grow in air.

5) I have a 100% success rate with my cloner. This is by far the easiest way to take cuttings.

6) I always leach and then flush for at least 2 weeks for buds that burn and taste clean.

7) I run a three part cycle. The plants stay 3 weeks in the cloner, then 3 weeks in the vegetative system and then the move to flower for the last 9 weeks.

Anyone can do this! If you can read a number you will have the same success as I do. Everything is measured and it is as easy as baking a cake.

If you follow my instructions you too can harvest a pound every 3 weeks.

So here we go...

Into the Cloner

I take the 2"-4" cuttings and place them in the Neoprene sleeves and into the 2" net pots. No spraying, dipping or anything! Just stick them in the cloner and you’re done.

My cloner is homemade. I have a 100% success rate with this system. I use tap water with 150ml of Clonex clone solution although no rooting hormone is actually needed. It does root a little faster with the solution.

The cloner is running on the same timer I use for all of my aero setups. 1 minute on and 5 minutes off.

The clone system is under a 24", 2-light, HO fluorescents.

I use EZ-Clone sprayers for everything. I run a 396 GPH pump for all the systems also.

Use an 18gal. Rubbermaid Roughneck container for your clone unit. Everything else will leak! Trust me on this, I've tried them all.

1/2" PVC pipe is used for sprayer assembly. Use an 11/64" drill bit for the sprayers. Just screw the sprayers right into the PVC pipe.

Check out the plans for a more detailed example.

Roots pop within a few days.

After a few weeks the plants start to develop a nice root system. I don't feed them any nutrients yet.

After the cloner it's off to the vegetative system


After 3 weeks the best 14 plants move to the vegetative system.

I use a dual container aeroponic system. The roots grow straight down which makes the plants easy to transfer to the flower room when the time comes.

The plants are under a 250W MH light set to 18/6.

Again, all my systems are on the same timer set to 1 minute on and 5 minutes off. This gives the roots the maximum amount of Oxygen without letting them dry out.

I run this nutrient formula for vegetative growth:

Botanicare Nutrients:

126ML Cal-Mag Plus
180ML Liquid Karma
540ML Pure Bend Pro Vegetative Formula

I start at 1500 PPM and bring it up to 2000 PPM by the second week of veg. I change the nutrients every 3 weeks with each new crop.

I adjust my PH to 5.8

Power Outage

I recommend using a UPS like you would use on your computer. The size would depend on how many pumps you are using. Remember, the pumps only run for 1 minute every 5 minutes so they don't use much power.

A large UPS will keep your plants safe for days. Your ice cream is a different story though.

Of course during any power outage you will always be without light unless you have a generator.
[FONT=&quot]
[/FONT]Moving on to the flower room.


When the time comes I just pull them up out of the containers and move them into the flower room.

I have 2 - 1000W HPS for a total output of 290,000 lumens. My lights have vented hoods the take the air from one room and vents into the attic. That way my room is totally sealed to keep the CO2 in the room. I use a 440 CFM fan to vent my lights. Lights are run at night to help keep temps down.

I use an A/C unit during the heat of the summer but don't need it the rest of the year.

I use a complete greenhouse control system with CO2. I keep my CO2 at 1500 PPM during the day cycle.

I keep my humidity below 60% and have a 200 CFM fan that vents into the attic to keep humidity in check.

I'm running 3 separate Aero/NFT systems so I can have 9 weeks flower time and a 3 week perpetual harvest cycle.

I use a cycle timer for the pumps. The timer is set to 1 minute on and 5 minutes off. This allows maximum Oxygen to the roots without letting them dry out.

I made 3 separate Aero/NFT systems using PVC fence posts. The plumbing runs inside and is made from the same 1/2" PVC pipe I use for the cloner. EZ-Clone sprayers between each plant site.

14 plant sites. 396 GPH pump.

The frame is made from 3/4" PVC pipe. 18gal. Rubbermaid container for the reservoir.

Here is my formula for my flower room:

Botanicare Nutrients:
126ml Cal-Mag Plus
150ml Sweet
180ml Liquid Karma
540mlL Pure Bend Pro Bloom

The Mix


Mix all the nutrients in a spare gallon milk container. Add water and shake well. The whole mix will take an 18 gal reservoir to 2900 PPM.

Add about half of the mix and check your PPM. It will be low so you will have to keep adding nutrients until you get it to 2000 PPM.

It is easy to add more nutrients but hard to take them out If you go over you have to drain some nutrients /water from the res and add more plain water.

That's why you want to take it slow at first.

Always adjust your PH after you set your nutrients PPM.
Fill the res with water and start adding the nutrient formula until it reaches the correct PPM.

What PPM level you run depends a lot on what strain you are running. 1700-2000 PPM is a safe number to start at but some strains can handle over 3000 PPM.

Every couple of days I add water. As the plants use up the nutrients you will have to add more formula. It's really too easy!

All you need is a cheap PPM meter. You need a PPM meter that goes to at least 2000 PPM. Stick it in the water and read the number.

Same with PH. Just put the meter in the water and it will tell you the PH. If it is below 5.8 you add PH up. If is above 5.8 you add PH down.
[FONT=&quot]
[/FONT]Flushing 101


Have you ever smoked pot that has that smelled like freshly mowed lawn clippings and had a burning after taste? Did it snap, crackle and pop like a bowl of Rice Crispies?

You just smoked pot that wasn't flushed properly.

Flushing is one of the most important aspects of growing. Some will argue that it is not needed. Don't listen to them! Trust me on this, flushing really helps improve the smell and flavor of your bud.

I start my flush 2 weeks before harvest. I drain the reservoir and fill it with tap water.

I let the pump run constantly for about an hour to wash out any nutrients hanging around.

Then I drain the reservoir and refill it. I add 150ml of Clearex and let the pump run normally for 24hrs.

After one day I drain the water/clearex and run just straight water for the next two weeks.

I always keep my PH at 5.8

I check the reservoir every couple of days. If I see the PPM climb more than 50 PPM I'll do another reservoir change.

Your plants will start to turn colors during the flush. This is good. It means that the plant is using up all the available nutrients.

I've seen purple, red, yellow and blue during the flush.

At the end of 2 weeks your plants should be ready for harvest.
[FONT=&quot]
[/FONT]Harvest time!


Now it's time to reap the rewards of all your hard work!


Towards the end of your flush you need to start checking the trichromes with a strong magnifying glass or a microscope.

If you have a camera with macro capabilities you can use that to inspect the buds.

You are looking for the trichromes to turn from clear to cloudy. I like my mostly Indicas with a little amber in the trichromes but I like my Sativas so that the trichchromes are just starting to turn cloudy.

If you harvest early in the window the high will be more of a head high. Also the more you smoke the higher you get. This is called the ceiling of the high. Sativas are well known for this type of high.

If you harvest later in the window you will get more of a body high. You know that couch lock feeling you get when you smoke a lot of hash like bud. Indicas and Afghani are the strains I think of for a body stone.

Now you have to factor in the fact that different strains are a mixture of Indica and Sativa. Then take into account that each strain takes a different amount of time to finish and you can have your hands full in no time.

So it's a personal thing, not an exact science. You choose what you like best. There is no exact day you can harvest but the time when you harvest effects the final high of the bud.

For me it works out like this. I like two main types of medicine. The first is better for the day. The second works better for the evening.

My more Sativa strains are harvested at the early side of the window. This gives me that soaring, energetic high that keeps climbing the more you smoke. It's great for work and play.

At around 9 weeks the more Indica strains are very finished. This is late in the window for them. The high is very body like and medicinal. It works great for pain and nausea. Or when you need to get to sleep.

I get the best of both worlds at 9 weeks.
[FONT=&quot]
[/FONT]Time to cut.


So now we have watched the trichromes and decided it is time to cut our babies.

I use some gardening shears and just cut them off at the base. Once I cut all the plants I turn off the pump and let the roots dry out. That way it is not so messy with wet slimy roots everywhere.

You have two options with the plants.

1) Hang the plants to dry and trim the buds later.

Advantage: Hanging them up allows the maximum drying time. This allows the plants to get rid of any leftover nutrients in the buds so they taste nice and sweet.

Disadvantage: It takes longer to dry this way. It is harder to trim the buds. You have to watch for mold. A longer drying time could allow mold to develop.

2) Trim the buds now and put them on a screen to dry.

Advantage: It is a lot easier to trim the buds when they are fresh. Mold problems disappear. Faster drying time. If you need smoke, trim first.

Disadvantage: Not much if you have flushed properly. The buds could dry too fast. Crispy on the outside and wet on the inside. Putting the buds in a brown paper bag can be used to slow the dry down.

I do both and really can't tell the difference in taste. But then again I flush the hell out of my plants before I harvest.

It's a lot easier to pull a plant and trim it right then. That way you are done right away and can move on to maintenance.
[FONT=&quot]
[/FONT]Trimming and curing


If your stems snap when you bend them then your buds are dry and ready for curing.

Curing is the last process of growing. It allows the smoke to smooth out and taste better. Bud that is harsh to smoke right after drying will many times mellow out with time.

If you haven't trimmed the buds go ahead and do the dirty deed.

I cure my bud in the classic glass jars used for canning. Any brand will work fine.

Don't pack the bud too tightly, you want them to breath.

Open the jars a few times a day for the first week. Then open them every few days until they smell sweet.

If they start smelling funky then you didn't let them dry enough. Take them out and let them dry completely.

It usually takes a good 3 months for the best cure. Like fine wine the longer bud cures the better it will taste.
[FONT=&quot]
[/FONT]Maintenance and cleaning


Taking care of the different systems is really quite easy.

Every harvest I clean and change all the reservoirs.

Each system has a garden hose fitting and valve. I attach a garden hose and run the hose into the bathtub.

Open the valve, plug the pump in and drain the reservoir. Double check your hose so you’re not spraying water all over the bathroom!

Listen for a sucking sound from the pump. That tells you it time to unplug the pump.

Don't forget to close the valve at this time!
I heard about a guy that sprayed water all over himself like a total idiot because he forgot to close the valve. I don't want to mention any names but it starts with stink and ends with bud.

Get a garden hose adapter for your sink and attach your hose. No need to haul water around unless you like that sort of thing.

Don't get stoned while you are filling your reservoir!
Don't ask me how I know this...

After harvest I remove all the plant matter and clean everything with bleach water. I run a little bleach in the water for a couple of hours and then flush with plain water a couple of times.

I really clean the shit out of all my stuff every harvest. You want your grow rooms as clean as a hospital. Actually cleaner would be better.

I always have a complete set of clean sprayers. I replace the sprayers every harvest and put the dirty ones in a cup of soapy water. Then later I scrub the sprayers with my wife's toothbrush (just kidding).

That way I always have a clean set of sprayers ready to go.
[FONT=&quot]
[/FONT]CO2 basics


Time to talk about air. Your plants need lots of Carbon to make the sugar that powers growth.

The Carbon comes from the CO2 in the air. Your plants can use a lot more CO2 than what is in the air normally. That's where adding CO2 comes into play.

If you increase your CO2 to 1500 PPM you can increase your plants growth rate. I went from 12oz. to over 16oz. per harvest using CO2.

Don't mess with yeast or tablets or all that other crap. You have two real options.
1) CO2 tank
2) Propane burner

I've never used a propane burner so I'll talk about using a tank and regulator.

The cheapest way to use a tank is with a timer. Go to this site and put in your room's dimensions.

CO2 Calculator - Greentrees Hydroponics

Figure out what it would take to fill your room in 15 minutes and set your valve to whatever the calculator tells you to. Set your timer to come on for 15 minutes 5 times a day. Keep it off during the night.

You can check your CO2 level with a testing syringe. You can buy them at most hydro stores. You draw in 100cc of air and then push it through the glass test tube. You read the purple band and it tells you your CO2 PPM.

By far the best way to control CO2 is with a controller. The controller I use checks the CO2 level and turns on my tank regulator when needed.
[FONT=&quot]
[/FONT]Temps and Humidity 101


Let's talk a little bit about air quality.

The plants don't need fresh air, they need CO2.

Having to keep your temps down and bringing in fresh air can all be solved by going to CO2 and a dehumidifier system.

CO2 lets you run higher temps so you don't need to vent as often. Temps can be controlled by A/C.

The only thing you will have to worry about is humidity. Solved by a dehumidifier or vent fan.

I know, you can't afford all this right away. That's OK. You can add as you grow.

Start with vented hoods and vent them outside the room. I vent into my attic. Then when you can afford CO2, you will only have to hook up the input of the fan to draw air from outside the room.

You need plenty of oscillating fans in your room to keep the air circulated well. The leaves of your plants should be moving at all times.
[FONT=&quot]
[/FONT]Genetics 101


By far the most important aspect of your grow is choosing a good plant strain to start with.

The best system in the world will grow crappy buds if you start with crappy seeds. Now granted they will be BIG crappy buds but crappy none the less.

I'm not going to go into detail about everything. There are books for that. I just want to cover the basics in regards to my own personnel experience.

There are two main types of plants. Indica and Sativa. Some group Afghan as a separate type but for this discussion we will group Afghan with Indica. Let's not deal with Ruderalis strains because you can't clone them.

Indicas: Plants are short and stocky. Buds are dense and covered in resin.
Smell and taste goes from sweet to hash like. Smoke is dense and will make you cough. Load small hits or be prepared for the coughing frenzy of death.
They finish in a short time compared to Sativas. Usually within 8 weeks.

The stone is heavy and physical. Think couch lock.

My favorite Indica is Mango. It looks like a classic Afghan. Warning! Too many hits and its nap time. I'm not into pure Indicas myself. Love the taste but not the stone.

Sativas: Plants grow tall and lanky. Buds grow light and airy indoors.

Taste is sweet and fruity. Smoke is light and tasty. You can load hero hits and be the man about town.

Sativas take forever to finish, sometimes longer. You will be setting around for months saying "What the fuck"? 12 weeks to finish is not uncommon.

The stone is energetic and cerebral. A real creative high. The more you smoke, the higher you get. Smoke too much and you might get paranoid though.

My favorite Sativas are anything with Haze. Silver Haze is unreal! The first time I smoked it I got so fucking paranoid I just about shit myself! Think Speed Weed.

I wish I had the space and time to grow pure Sativas. Good thing that there are mixes that gives you the best of both worlds.

Indica/Sativa mix: This is pretty much all I grow. Anyone can find a strain that suits them best.

Finish times can be between 8-10 weeks depending on the strain.

The size can vary. Cropping may have to be used on taller strains.

Some strains have more Indica in them. My favorite is Blueberry. It is 80% Indica. It is by far the tastiest weed I have ever smoked. You have to grow this strain! Trust me on this. Great for movies and gaming.

Strains with equal Indica/Sativa are my main day smoke. AK47, Bubblegum, Purple Silver all fall into this category. They have an energetic high like a pure Sativa buy also have a nice mild body stone like an Indica. Balance is the key.

The most Sativa I run in a strain is 80% in my Skunk #11. I love that classic skunk taste and smell. I wish I could find a quicker and shorter variety of Skunk though.

So there you go. The condensed version of Genetics. You could write a book on the subject and still never cover everything. You have to start somewhere though.

Your success is 100% dependent on finding the right plant. Don't underestimate the importance of finding good genetics to start with.

In the Navy we had a saying...
Shit in, Shit out.
[FONT=&quot]
[/FONT]Let's talk about Aeroponics


I'd like to talk about growing in general and the concepts that produce fast growth. I'd to keep it simple so anyone can understand.

Plants have needs just like you and me. The biggest difference is that plants make their own food. To put it simply, plants make sugar and the sugars power plant growth.

So what does a plant need to make sugar? Carbon, Oxygen, Water and light. They also need small amounts of nutrients and of course Chlorophyll.

The plants take in the Carbon (CO2) through the leaves. They take in water and nutrients through the roots. What most people don't know is plant also take in their Oxygen through the roots.

Because plants give off Oxygen many believe O2 is a non issue. In realty it's usually the determining factor in maximum plant growth.

So if you look at what a plant need it's obvious where the bottle necks can occur.

Light is the most important element in any growing. Light is what powers photosynthesis. The more light the faster the plants grow, it's that simple.

Water and nutrients are a non issue. Why? Who has ever had a problem over watering and over fertilizing? I have. It's easy to give too much water and drown your roots. Too much nutrients and you burn the shit out of them. So the problem is not giving the plants enough water and nutrients...it's usually giving them too much!

Carbon is one of the building blocks of sugar. The plant needs lots of CO2 for fast growth. Normal air is between 200-500 PPM. Not much compared to what the plant can actually use. Plants can easily use 1500 PPM or more.

Oxygen is probably the most overlooked elements in plant growth. Even though plants give off more O2 than they take in, they still use a lot of Oxygen in the sugars they make.

My system addresses each one of these issues.

Light is right. You already know how to add more light.
Water and Nutrients are fed and monitored perfectly.
Carbon is added with a CO2 system.
Oxygen is the main advantage of my Aeroponic system.

Think of it this way...the plant breaths in Oxygen through its roots and out through its leaves. So imagine yourself a plant and let's do a test:

1) Dig a hole in some dirt. Stick your head in it and fill it back up. Now take a deep breath. This is what growing is soil is like.

2)
Now fill a container with water and stick your head in it. Oh yea, don't forget to add some air stones first. Now take a deep breath. This is DWC.

3)
Now just take a normal deep breath. This is Aeroponics.

Am I getting my point across?
[FONT=&quot]
[/FONT]Cloner Build Tutorial ver1.1


Step 1 – Cutting the ½” PVC Pipe

1) Cut eight 7” lengths .
2) Cut two 1½” lengths.
3) Cut one 2¼” length.

Step 2 – Preassemble Your Sprayer Frame
1) Start with the top “H”. It’s made from the 3 – Tees & two 1½” pipes.
2) Add the elbows to the tips of the “H”.
3) Add the 7” legs and end caps.
4) Attach the 2¼” pump connecting pipe to bottom of the “H”.

Step 3 – Drilling the Sprayer Holes
1) Measure and mark the sprayer holes according to the plans.
2) Use the 11/64” drill bit for the eight holes.

Step 4 – Drilling the Lid
1) Measure out 23 holes as shown in the plans.
2) Use the 2” hole saw to cut the holes.
3) Use the Exacto Knife to clean up the holes.
4) Cut a small hole with the Exacto knife just big enough for the cord to fit through.

Step 5 – Final Assembly
1) Place the pump and sprayer unit into the container and check to make sure everything fits well.
2) Take apart the sprayer unit and paint primer on the ends of the pipes and inside the fittings.
3) Start the final assembly on the sprayer unit. Be careful because the glue dries fast! Do only one
part at a time until the unit is completely assembled.
4) Screw in the sprayers. You may need to use a pair of pliers to get them in.
5) Cut down a neoprene collar to the size of the cord hole you cut in the lid.
6) Run the cord through the lid and neoprene collar. Don’t put the lid on yet.

Step 6 – Setup and Conclusion
1) Add enough water to cover the pump but don’t fill it over half way. We don’t want the roots to
hang in the water.
2) Add 150ml of Clonex solution to the water (optional) and adjust the PH to 5.8
3) Set your cycle timer to one minute on and five minutes off.
4) Put the lid on the container.
5) Fill the cloner with your favorite strains. Don’t spray the cuttings.
6) Enjoy your new cloner!!!! You should see roots within a week.
7) Don’t forget to pass the love on…
[FONT=&quot]
[/FONT]Vegetative unit tutorial vers 1.1


Step 1 – Cutting the ½” PVC Pipe

1)Cut seven 7” lengths.
2)Cut 1 10” length.
3)Cut two 1½” lengths.
4)Cut one 17¼” length.

Step 2 – Preassemble Your Sprayer Frame
1)Start with the top “H”. It’s made from the 3 – Tees & two 1½” pipes.
2)Add the elbows to the tips of the “H”.
3)Add the 7” legs and end caps.
4)Add the 10” drain pipe to the “H”. Do not attach the ball valve yet.
5)Attach the 17¼” pump connecting pipe to bottom of the “H”.

Step 3 – Drilling the Sprayer Holes
1)Measure and mark the sprayer holes (according to the plans).
2)Use the 11/64” drill bit for the ten holes.

Step 4 – Drilling the Lids & Containers
1)Measure out 18 holes as shown in the plans.
2)Use the 2” hole saw to cut the holes.
3)Mark the exact center inside the plant container. Cut a 2” drain hole.
4)Cut a 2” drain hole in the exact center of the reservoir lid.
5)Cut a 2” access hole in the corner of the reservoir lid so you can see and maintain water level.
6)Cut a 13/16” hole in the side of the plant container for the drain valve (according to the plans).
7)Use the Exacto Knife to clean up the holes.

Step 5 – Final Assembly
1)Place the sprayer unit into the container and check to make sure everything fits well.
2)Take apart the sprayer unit.
3)Start the final assembly on the sprayer unit. Start applying glue to each piece. Be careful because the glue dries fast! Do only one part at a time until the unit is completely assembled.
4)Screw in the sprayers. You may need to use a pair of pliers to get them in.
5)Put the pump in the reservoir and attach the down pipe.
6)Put the reservoir lid on and place the plant unit on top.
7)Connect the sprayer unit to the down pipe (pump).

Step 6 – Mixing the Nutrient Formula

Botanicare Nutrients:
1)126ML Cal-Mag Plus
2)180ML Liquid Karma
3)540ML Pure Bend Pro Vegetative Formula

Mix all the nutrients together in a gallon jug and top off with water. Shake well!

Step 7 – Setup and Conclusion
1)Add 15 Gal. of water. (approx.) to the reservoir
2) Add nutrient mixes until the meter reaches 2000 PPM
3)Adjust the PH to 5.8
4)Put the lid on the plant unit.
5)Fill the vegetative unit with your favorite strains from the clone unit.
6)Set your cycle timer to one minute on and five minutes off.
7) Enjoy your new vegetative unit!!!! You should see amazing growth rates.
Don’t forget to pass the love on…

Aero/NFT Tutorial vers.1.1

Step 1 – Cutting the ¾” PVC Pipe for the Frame

1) 4 - 41” lengths (label plant support)
2) 4 - 20” lengths (label “H”)
3) 6 - 4 1/8” lengths (label fence post holder)
4) 3 - 14 3/4” lengths (label 1- “H” and 2 -“end”)
5) 4 - 18” lengths (label plant support leg)
6) 4 - 12” lengths (label plant support leg)
7) 4 - 2” lengths (label end)
8- 2 - 12 1/2“ (label front)
9) 2 - 13 1/2” (label back)

Step 2 – Preassemble Your Frame
1) Start with the ends. Use 4 - Tees and 3 – 4 1/8” lengths to make the fence post holder.
2) Add the legs and bottom Tees. Don’t forget the front and back label!
3) Add the 2” pieces to the bottom of the Tees
4) Add the Elbows to the 2” pieces. Make sure the elbows are facing toward each other.
5) Connect the Elbows with the 14 ¾” pieces. The ends should be complete now.
6) Now make the bottom “H” using 2 - Tees, 4 – 20” pieces and 1 – 14 ¾” piece.
7) Connect the two ends together using the “H”.
8- Create your plant supports using the 4 – 41” lengths and 4 – Elbows.
9) Add the 12” and 18” plant support legs and place the plant supports into the frame.
10) If everything fits then take the unit apart and glue all the pieces together. Be careful, the glue
dries fast!

Step 3 – Assemble the Fence Posts
1) Measure and mark the 2" net pot holes (according to the plans).
2) Clean up the holes with the Exacto knife.
3) Put a large bead of Silicone inside 2 of the end caps and place them on the back end of the fence
posts.
4) Run a bead of Silicone around the edges of the end cap and let the posts dry
5) Cut the bottom ¼” off of the 2 end caps. Use a small drill drum sander to sand an opening for the
sprayer pipe assembly. A Dremel tool works well too.
6) Place the fence posts on the frame and use large cable ties to hold it in place.

Step 4 – Cutting the Sprayer Assembly Pipe
1) 2 - 3” lengths
2) 2 - 2” lengths
3) 2 - 47” lengths
4) 1 - 11 1/2” length

Step 5 – Assembling the Sprayer Unit
1) Drill ten 11/64” holes in the 47” length pipes according to the plans
2) Use pliers to insert the EZ-Cloner sprayers into the holes
3) Attach end caps and elbows to the sprayer pipes
4) Put the 2” pipes into the elbows
5) Combine the two sprayers together with a Tee
6) Add another 2” piece to the Tee and a downward facing Tee to that
7) Attach the last 2” piece to the Tee.
8- Attach the ball valve and garden hose adapter to the last piece
9) Try it out in the fence posts and if everything looks good, glue it all together.

Step 6 – The Container Lid
1) Put the container and lid under the fence post and draw a drain hole under the fence posts.
2) Cut out the holes with a utility knife and clean up the edge with the small drum sander.
3) Drill a 2” hole for the pump pipe.
4) Cut a large access hole with the utility knife. Leave one edge attached to make a flap that can be
closed.

Step 7 – Final Assembly
1) Place the pump into the container and run the 11 ½” pipe through the lid.
2) Put the sprayer assembly into the fence posts.
3) Put the container under the frame and attach the pump pipe to the sprayer assembly.
4) Apply a few small drops of silicon the drain end caps and place them on the fence posts. Don’t
use much silicon because you want to be able to remove the caps when needed.
5) Fill the containers and place empty net pots with collars into the fence posts.
6) Check for leaks. If everything is OK then you are done! Congratulations!!!

Step 8 – Mixing the Nutrient Formula

Botanicare Nutrients:
1) 126ml Cal-Mag Plus
2) 150ml Sweet
3) 180ml Liquid Karma
4) 540ml Pure Bend Pro Bloom
Mix all the nutrients together in a gallon jug and top off with water. Shake well!

Step 9 – Setup and Conclusion
1) Add 15 Gal. of water. (approx.) to the reservoir
2) Add nutrient mixes until the meter reaches 2000 PPM
3) Adjust the PH to 5.8
4) Fill the flower unit with your favorite strains from the vegetative unit.
5) Set your cycle timer to one minute on and five minutes off.
6) Enjoy your new Aeroponic system!!! You should see some amazing buds in no time!
7) Don’t forget to pass the love on…
 

Attachments

flabbyone

Well-Known Member
You should call this the Stinkbudponics System :joint: as this is not just a formula, it is the complete system.
What cha think stinky?
 

evan0387

Active Member
Stinkbud, amazing!! I'm pretty new to this forum, and I love reading everything you have posted. Thanks for spreading the knowledge!

The PVC frame that houses the fence posts, are they just there to support the plants and hold the posts up, or do they serve as a way to feed the plants as well?
 

SVINIAR

Active Member
This is the best post I've read.. +rep to ya StinkBud.

I'm gatherin shit now for this, and then Earl's WidowCindy is gonna be the culprit.. :D
Been waitin to sprout these.
 

chicoles

Well-Known Member
Impressive beyond belief.

How long did it take to perfect this system? Trial and error or are you mentored? Its like four years of college wrapped up in that one recap post.

thank you!

:peace:
 

towelieban

Active Member
Thank you Stink. I had been put in charge of figuring out hydro, with this plethora of great aero info I am ready to rock. The damn thread took me 5 hours to read! Many thanks for getting all of the info into pdf format. Respect.
 

DoobyDoo

Well-Known Member
Holy crap StinkBud. Freakin' impressive! I've been reading this thread for a while, and I do believe this system is the answer to how I get a hydro-style grow going without spending massive amounts of dollars on commercial equipment.

THANK YOU for posting all these plans! Now I've gotta figure out how to modify them so it all fits in my space :)
 

StinkBud

Well-Known Member
Impressive beyond belief.

How long did it take to perfect this system? Trial and error or are you mentored? Its like four years of college wrapped up in that one recap post.

thank you!

:peace:
I grew for 14 years using soil. My mentor helped me a lot with hydro. He's the one that told me about the organic nutrients. I bought a system online (payed too much). I learned the ins and outs of aero with that system.

Then I started thinking of ways to improve it. Mostly trial and error at that point.
 
Top