lets make some colloidal silver and fem some beanz aka selfing my banana puff

ok lets get to it. took 6 clones, gonna reverse 2 to hit 4 others and keep the healthiest to repeat. gotta clean up the silver n were good to start brewing. im aiming for HIGHHHHHHHHHHHHHHHHHHHHHH ppms like 100 and will be treating fewer times. also gonna run terisias spray side by side for comparison. ill use all these this round n just clone one of the fems before flipping. it is gonna be fucking raining fems in thizz bitch!!!!!!!

https://www.youtube.com/watch?v=78Y7-iVOjVU

YACSP ....yet another colloidal silver post ....lol ......subbed

Gotta keep an eye on this I'm in the process of trying to turn a branch on one of my plants. Not sure how many times to spray a day, so I've been doing it 3 times.

SirGreenThumb said:

Gotta keep an eye on this I'm in the process of trying to turn a branch on one of my plants. Not sure how many times to spray a day, so I've been doing it 3 times.

Click to expand...

3 times may be necessary if you are using a solution that is less then 30 PPM or if the plant doesn't start showing "balls" within about 2 weeks. If your solution is 40-45 PPM which is recommended then you should only have to spray once daily. Also remember it is not advisable to smoke or ingest any parts of the plant you have sprayed. Good Luck and keep us posted.

i read using over 100ppm you can treat every 2 or 3 days. well see...

OP I was trying to read the output voltage with my old eyes and it would appear that it is 5 volts. The recommended voltage to produce quality CS is 30v which can be approximated by hooking 3 9v batteries in series as is shown in this tutorial https://www.rollitup.org/do-yourself/773401-90-minute-colloidal-silver-production.html#post10029551

i think the 1A current output should makeup for the lack of voltage. nice thread there too! hot water is what could have fucked with your ppm readings, imo.

CaretakerDad said:

3 times may be necessary if you are using a solution that is less then 30 PPM or if the plant doesn't start showing "balls" within about 2 weeks. If your solution is 40-45 PPM which is recommended then you should only have to spray once daily. Also remember it is not advisable to smoke or ingest any parts of the plant you have sprayed. Good Luck and keep us posted.

Click to expand...

I'm using 50ppm;
This is what I have. I've only been spraying one branch of an auto, but its only been like 4 days since I started.

greenghost420 said:

i think the 1A current output should makeup for the lack of voltage. nice thread there too! hot water is what could have fucked with your ppm readings, imo.

Click to expand...

If you read down the thread a ways you'll see that I did discover that taking the reading while the solution was hot did give a falsely high reading, about 1.5 times actual value. Heating the solution is to speed up the reaction, just basic physics/chemistry, and does not have any other effect.

i liked the idea. seems like common sense.

good luck sirthumb, keep me posted

skunk vol 9 issue 1 pg 72 ed rosenthal says 120ppm and treats 3 times over 10-12 days.

greenghost420 said:

skunk vol 9 issue 1 pg 72 ed rosenthal says 120ppm and treats 3 times over 10-12 days.

Click to expand...

Yay and ed rosenthal gave his only begotten son that you might
Prosper from feminization. Lol quoting the man down to the page, nice!

Ill be watching, im curious to see how the clones fair at such a high ppm

I like giving credit where its due

Let me know how long it takes you to get 100+ PPM with your set up, I will be pissed if I spent $49.99 on a 0-30v, 0-5A transformer for nothing.

Youll be watching right? Then pay attention...lol

ok just setup everything, started at 930. 1 cup of h2o. lets see how long to get to 100ppm....

banana puff clones are rooting up nicely as well....

at 5ppm...lol

wish my silver pieces were bigger, as well more voltage lol