Budmasterflash
Member
So I'm making this DIY because I was overwhelmed after making a post in the 600 Club thread.
I got so many requests for me to make and ship to people all over that I cant keep up.
Most of the things needed can be got from the dollor store J
I'm willing to still make and ship for the non DIY people out there but it does take me time to build and will be setting up a paypal account for hassle free payment and shipping.
So here it is the Budmasterflash DIY MICRO SCRUBBER
List of parts
90mm 120VAC 35CFM fan
Active carbon small bag
Pen holder
2- 4x4 inch 1/8 thick wood
Charcoal window screen
Plastic mesh
1/8 inch 2 sided foam tape
Fishing line
Nuts/bolts and washers
Plug and cord
Printer paper
Tools needed
Drill
2 inch, 3 inch and 3 ¼ inch hole saws
Drill bits
Wood glue
Ducting tape
Scissors
HOW TO
Take the 2-4 inch square wood and find the center
Take 1 and cut out the center with 3 inch hole saw and save the the center part for the next step. With the 2 inch hole saw cut out the center of the part u saved and again save the center of that. Take the other 4 inch square and cut the center out of it using the 3 ¼ inch hole saw
Take your pen holder and some charcoal screen and line the inside, This holds the carbon in.
Get the 2 inch center, plastic mesh, charcoal screen and fishing line. Wrap the plastic mesh around the 2 inch center and trim, then stitch the mesh into a tube and insert the 2 inch center into 1 end and glue it. Wrap that in charcoal screen and tape it along seam. This acts as the air chamber.
Get the 4 inch square with the 3 inch hole and 2 strips of charcoal screen and glue, glue the screen onto 1 side gluing 1 at a time and be sure to cross the mesh. Put to the side and let dry while u do the next step
Take the pen holder, center chamber and carbon. Fill the outside space with carbon all the way to the top, be sure not to get carbon on the wrong side of the charcoal screen.
Take the 3 inch ring and printer paper, trace the ring and cut out the paper. This acts as part of the gasket. Put the paper and 3 inch ring on top of the carbon and push down until it is flush with the top of the pen holder and your chamber
Take the 4 inch squares, nut/bolts and 1/8 2 sided tape. make the holes for your fan and drill both at the same time that way the holes line up. On the 4 inch square with the 3 ¼ inch hole line the edges with 2 sided tape leaving the face up side with the paper on it still. Acts like a seal but makes it easy for replacing carbon.
Wire your fan with the plug end, I used an old plug off a bad toaster
Take your 4 inch square with 3 ¼ hole,tape and bolts on. Put the pen holder in the center, line up the 4 inch square with the mesh and press it together, Go slow and dont spill, line up your fan and then bolt it all together.
BAM ! u got a Budmasterflash micro scrubber
roll a spliff and pat yourself on the back
I got so many requests for me to make and ship to people all over that I cant keep up.
Most of the things needed can be got from the dollor store J
I'm willing to still make and ship for the non DIY people out there but it does take me time to build and will be setting up a paypal account for hassle free payment and shipping.
So here it is the Budmasterflash DIY MICRO SCRUBBER
List of parts
90mm 120VAC 35CFM fan
Active carbon small bag
Pen holder
2- 4x4 inch 1/8 thick wood
Charcoal window screen
Plastic mesh
1/8 inch 2 sided foam tape
Fishing line
Nuts/bolts and washers
Plug and cord
Printer paper
Tools needed
Drill
2 inch, 3 inch and 3 ¼ inch hole saws
Drill bits
Wood glue
Ducting tape
Scissors
HOW TO
Take the 2-4 inch square wood and find the center
Take 1 and cut out the center with 3 inch hole saw and save the the center part for the next step. With the 2 inch hole saw cut out the center of the part u saved and again save the center of that. Take the other 4 inch square and cut the center out of it using the 3 ¼ inch hole saw
Take your pen holder and some charcoal screen and line the inside, This holds the carbon in.
Get the 2 inch center, plastic mesh, charcoal screen and fishing line. Wrap the plastic mesh around the 2 inch center and trim, then stitch the mesh into a tube and insert the 2 inch center into 1 end and glue it. Wrap that in charcoal screen and tape it along seam. This acts as the air chamber.
Get the 4 inch square with the 3 inch hole and 2 strips of charcoal screen and glue, glue the screen onto 1 side gluing 1 at a time and be sure to cross the mesh. Put to the side and let dry while u do the next step
Take the pen holder, center chamber and carbon. Fill the outside space with carbon all the way to the top, be sure not to get carbon on the wrong side of the charcoal screen.
Take the 3 inch ring and printer paper, trace the ring and cut out the paper. This acts as part of the gasket. Put the paper and 3 inch ring on top of the carbon and push down until it is flush with the top of the pen holder and your chamber
Take the 4 inch squares, nut/bolts and 1/8 2 sided tape. make the holes for your fan and drill both at the same time that way the holes line up. On the 4 inch square with the 3 ¼ inch hole line the edges with 2 sided tape leaving the face up side with the paper on it still. Acts like a seal but makes it easy for replacing carbon.
Wire your fan with the plug end, I used an old plug off a bad toaster
Take your 4 inch square with 3 ¼ hole,tape and bolts on. Put the pen holder in the center, line up the 4 inch square with the mesh and press it together, Go slow and dont spill, line up your fan and then bolt it all together.
BAM ! u got a Budmasterflash micro scrubber
roll a spliff and pat yourself on the back
