Recent content by maddmattmurdock

  1. maddmattmurdock

    Spider Mites Questions

    Ok its at your grocery store plus tablespoon neem oil, i have used dish soap it browned leafs some will not, olive oil and sunflower oil. Get twenty habanero peppers and dice ,not chop ,dice then steep in 1gallon simmering water not boiling.simmer means its scold you but not boiling. Boiling...
  2. maddmattmurdock

    DiY LEDs - How to Power Them

    http://m.ebay.com/itm/271535124000?&txnId=1358404781017 I found this!
  3. maddmattmurdock

    Led question is this normal

    I had that problem with countless timers on so much equipment i hated throwing away any of them, so i started using relays. The relay will completly disconnect all electricity from the circuit. I use digital on everthing with a relay they make 220 and 110v relays. No voltage leaks, can use your...
  4. maddmattmurdock

    DiY LEDs - How to Power Them

    I Guod i have a question about the pic. Please bear with me im not new to electricity just LEDs. I would like to understand more of the circuit you have should me. The resistor are after the COBs on the ground side and that is to stop the vf from running by 2w or am i looking at it and...
  5. maddmattmurdock

    DiY LEDs - How to Power Them

    Thank You Guod!!
  6. maddmattmurdock

    DiY LEDs - How to Power Them

    In the driver or COB? I would think the driver would be the same, but i do believe you are correct in the loss of efficiency on the Vero 18, but that will be regained in HVAC savings.
  7. maddmattmurdock

    DiY LEDs - How to Power Them

    Thank you for your help and passing on knowledge.
  8. maddmattmurdock

    DiY LEDs - How to Power Them

    Sorry Im a Noob at this. I was really into some Colorado Grape Ape 2012 when I asked the question. The driver is constant current driver. Driving power: 50w Model: 10 series 5 in parallel Input Voltage: 85V~265V Output Voltage: 32-34V Current:1750mA Efficiency > 88% Power Factor >0.98...
  9. maddmattmurdock

    DiY LEDs - How to Power Them

    I would like to power two Vero 18 off one 32-34v 1750ma Driver. I know i will need resistors inline of each COB. I have looked through some books and came up with this. I would like to see each 18 at 700ma-850ma. Resistor needed=Voltage Supply - Vf of LED/Total of desired supply...
  10. maddmattmurdock

    DiY LED - Cree CXA3070

    Got the Vero 18 5600k powered with a Meanwell Lpc-35-1050. The vf was 3-3.2 at 950ma.
  11. maddmattmurdock

    DiY LED - Cree CXA3070

    4CXA's, 4 VERO 18, 4 Reds ? Aluminum U Channel is the frame which is 22"x12" held together with aluminum rivets, 6/32 screws and 8/32 screws. Reinforced with L brackets to support any frame twisting. 4 2" x 10.5" Usaheatsink For the Veros 2 3.5"x10.5" Usaheatsink For the CXA's 4 CXA 3000k Z2...
  12. maddmattmurdock

    DiY LED - Cree CXA3070

    T Thank you, that is what i thought as well, we will see as the Veroa are on the way. Thanks for all the info!!
  13. maddmattmurdock

    DiY LED - Cree CXA3070

    SurpaSPL I have five free Meanwell lpc-35-1050 i was looking at the Vero 18 to run off this drivers. What do you think?
  14. maddmattmurdock

    DiY LED - Cree CXA3070

    BTW the amount of light compared to the six hundred MH it replaced the LED is much more brighter light, that is an eye measurement so take it for what its worth.
Top