Search results

  1. Cgravell23

    What did you accomplish today?

    Enough sssaaid!
  2. Cgravell23

    BHO vac purge "Muffining"

    Crumble, @ the end of your 3rd day the last 15-20 minutes of your purge i think your gradually turn your heat up to 145• then cool it back down to 64-72.(room temp) but if your working on a skillet like me, you’ll have to get started an hour or so before cause heating up your chamber in your “...
  3. Cgravell23

    Bho vacuum chambers

    Right that’s what one of my old bosses in the oilfield had told me, but yea i know folding the patty onto itself helps get the gas out and also when you go to re-purge it that you have to have the temp on your skillet back down to what temp your material is @ then gradually rise your temp back...
  4. Cgravell23

    Bho vacuum chambers

    Yea thats what i was thinking, that it would sound complicated trying to explain the process. But ok cool i got u, & yea ive found out that if u cant get any action on your patty then by pressing it onto itself can cause it to muffin/bubble up again. My bad for not knowing what im doing.
  5. Cgravell23

    Bho vacuum chambers

    So do I open my air inlet valve and let it loose suction and then close it off & re-vac it for 5/10 minutes or however long it takes for your muffin to drop then let it stabalize for 24/48 hours?
  6. Cgravell23

    Bho vacuum chambers

    What do u mean by keep pulling, like turning on my pump after its lost pressure with the pump valve closed @ first & then when your pump starts to run then u slowly open the pump valve for your chamber to regain negative pressure?
  7. Cgravell23

    Bho vacuum chambers

    Ok so if my vaccum chamber gauge is losing vacc can i just run it it for like a minute or 2 every 8/9 hours that it needs to re-pull a full vac by furning onbtbe pump & slowly opening the pump valve?
  8. Cgravell23

    BHO "whip tech" - How to crumble??

    So are you buying pounds from the dispensary & opening the package out on the table or wherever for a day or so then in the freezer with your butane for another two days and then putting your material in your blast tube & vacuuming it for like 2 to 3 minutes or however long it takes to reach...
  9. Cgravell23

    BHO "whip tech" - How to crumble??

    Ok i c, but ya i havent been able to make crumble like that. It didnt turn to goo but its like a shatter but still waxyy like just no flavor of terpenes
  10. Cgravell23

    Bho vacuum chambers

    does grinding the material really good help with more yield?
  11. Cgravell23

    Bho vacuum chambers

    OK well I’ve done three runs the first one did not go well at all because first of all my material was real real moist still & I ran the vac to suck air or whatever out of the column to allow more butane out after I had already put butane in my column and let it set for about 10 mins in it so...
  12. Cgravell23

    Bho vacuum chambers

    Alrighty thank u tons for the advice!!! But Doesn’t it stop bubbling after about 15 minutes?
  13. Cgravell23

    Bho vacuum chambers

    OK so when I put it in the chamber for vacuum & only let it run until it hits -30 and then close my valves immediately and turn off the pump and release the little bit of air that’s in the hose from my pump fitting and you’re saying it should bubble for a day or two? Or do I just run the pump...
  14. Cgravell23

    Bho vacuum chambers

    Well I was just wondering how I could get it to harden up a little bit it’s like maple syrup right now but actually a little bit thicker?
  15. Cgravell23

    BHO "whip tech" - How to crumble??

    How do u even get it @ the correct specific temps? A skillet or a heating pad? And how long are u running your vac? Just till it hits -30 and then turning it off?
  16. Cgravell23

    Bho vacuum chambers

    So to make it stable im gonna have to put it just in the chamber in a sleeping bag on the floor in the room and not purge or re-vac it or anything for three days @ room temp? and then put it on a skillet for the last 5 to 10 minutes and heat it up to 140° To get honeycomb?
  17. Cgravell23

    Bho vacuum chambers

    Yea i got some of that already
  18. Cgravell23

    Bho vacuum chambers

    R u talking about Oil slick Sheet (PTFE)?
  19. Cgravell23

    Bho vacuum chambers

    Also do i turn on the pump then slowly open the pump valve while slowly closing the air inlet valve simultaneously to get it up to vac? Or do i just have the air inlet valve all the way closed then turn the pump on & then slowly open the pump valve? I know to definitely close tge pump valve all...
Top