Search results

Honestly I cant say from personal experience. I have seen some of them being hit with a hammer over and over and not breaking. You could always get some small aluminium angle and make a frame and bolt the sheets to it. I had made a frame with 3/4 inch angle and my 3d printer and have no strength...

You dont need a vac chamber for welding aluminium. It is not something you can weld easy without experience. I have been a welder for almost 20 years and have done my fair share of it and still have issues with the stuff. with that being said on amazon there are some brazing rods that you just...

Looks like you got a tent with velcro flaps on it. I have a 4x4 that has them and they wont seal right light leaks all over the place. Check for light leaks. looks like you got some reveg going on there also.

USA

Well thanks for all the help today and the info. I tossed my 100 watt hlg led in the tent for now till I can figure something out with this one Enjoy your camping trip bob Have a good night folks

The breaker finally kicked off with only the light running. So I can leave the power supply plugged in with no issues (not connected to the lights) I cant run the light for a full 12 hours. I cant run the light with other things in the room on Maybe the wire I used isnt thick enough? Maybe I...

I have yes. It is still running but is so hot you cant touch it for more than a second or two. It will kick the breaker soon

ok it is wired and running. it is the only thing running in that room and on that breaker.

I just unplugged it. It did manage to get warm (it was above room temp you could feel the difference) while it was connected to nothing only plugged into the wall. its been about 2 hours plugged in.

I thought it might be one of them also when I first put this light in there so I ran it till it kicked while it was the only thing on. still sitting there just fine after all this time. In that room I have everything running right now. the heater, the dehumidifier and a 100watt hlg led. it is...

I will give it a shot and let you know. It takes a bit of time for it to kick it off normally an hour or so after its been running

Ill give it a shot. I soldier connections for the electronics I mess with all the time didnt think it would hurt with shrink wrap around the connection

Nothing new was added. the breaker is connected to 2 rooms (part of them anyway. ceiling light in one of the rooms and the outlets in another) The dehumidifier is the portable ac that was running with the 600 watt hps not it is set to dehumidify only (it has a few different settings)

Im not either at this point. it keeps kicking the breaker and I cant figure out why. The wire to the panels is red on both sides its all I had. Here is a pic showing where they are connected and kind of where they run to (the start and end panels)

The first pic is the wire going into the driver. Each board lights up and they are wired in series. I pulled all wires and rewired it just to make sure I didnt cross something somewhere and have the same results. I did leave the wires long on the back side since I changed the layout of the...

So I bought a 4 pack of the qb132 boards with an hlg-240h-c1750a driver. Got them wired in series as the hlg website recommends with this driver and I was told I would not need a heat sink but this light keeps kicking my breaker. I put a fan on the top of the frame blowing at the driver and it...

It gives actual power draw in the specs for the light on their website. I'm not an expert and have no actual info on what to do better for higher yields sorry. Just wanted to let you know where the actual draw was. Some of that is for fans and the driver of course

Have you grown any of the seeds in the past or is this a first for you?

Do you have enough room for both? If you by the 4x4 eventually you will buy the bigger one. Lol it worked out that way for me and many other people I know

Lmao The hlg 100 has its own driver. The 4 qb132 has the hlg-240h-c1750a driver. I want to take the Hlg-240h-c1750a from the 4 qb132 boards and use it on 2 qb288 rspec if i can. I hope that clears it up a bit.