Cloning

[Purple love]

Hi can some one point me in the direction of step by step on how to clone i took advise on here last time and this is what I have please some one with experience help thanks

 

[TCH]

Those should be moist and covered with a dome. The ridiculously dry cubes and low humidity don't seem to be working too well.

 

[MtRainDog]

yeah they are too dry for sure. Hydrate those cubes, and put them under a dome.

 

[Purple love]

Those should be moist and covered with a dome. The ridiculously dry cubes and low humidity don't seem to be working too well.

they have the cloning dome with the light ive been keeping it on a heating mat and spraying them

 

[TCH]

they have the cloning dome with the light ive been keeping it on a heating mat and spraying them

Dunk those cubes to get them moist all the way through.

 

[HydroKid239]

As stated above.. dome them, and use something to elevate them from being directly on the heat mat unless you are controlling the temp. Mist the cubes, and keep them moist. Spray mist multiple times daily if needed.

 

[Purple love]

yeah they are too dry for sure. Hydrate those cubes, and put them under a dome.

i did i do it 2 ti,mes a day they are moist juts look like that because of picture

 

[TCH]

How long have they been in there?

 

[Purple love]

As stated above.. dome them, and use something to elevate them from being directly on the heat mat unless you are controlling the temp. Mist the cubes, and keep them moist. Spray mist multiple times daily if needed.

i do all that exept for the elevate part il do that are they dead should i start over

 

[Purple love]

Dunk those cubes to get them moist all the way through.

i did that i also spray them cubes to keep them moist and humidity up

 

[HydroKid239]

i do all that exept for the elevate part il do that are they dead should i start over

I would. Make sure you are taking cuts from a healthy plant. Gives them a better chance. They don’t need a ton of light either. You could use a small desk lamp to keep them going if that’s all you had available.

If all else fails.. take a cut and place it in a cup of water.
I’ve had this cut in a beer bottle sitting on my stove with only the lamp from the hood over the stove. It’s been sitting there about a month.

 

[Liamp1603]

I found with the root riot cubes it was best to soak them in a weak veg solution .... but after trying loads of times and not having a very high percentage I bought an aero cloner and I'm around 90 percent success with one of these simply snip the cut prune the leaves set it and forget it .. best piece of kit I've ever bought

 

[crimsonecho]

cloning is like a freaking nightmare to me haha sometimes i get close to 100% sometimes same technique same plants 0% so i keep trying every method till they dont work anymore. i even put together a water cloner with uv aquarium filter without airpumps and stones. just filter sucking water doing its thing inside and depositing the sterilized water from the other end of the water cloner from some height. thus aerating water in the process. worked really well.

 

[cannabiscrusader]

Raise them off the heat mat a bit with some bottle caps, or a few rings from a Mason jar lid. Some of those heat mats just keep on running. Make sure the vents on the dome are open. The light built into the dome along with the heat mat are roasting your clones. Mine root just fine using the side wash from my veg lights, which are actually underneath my dome.

Don't let them sit in water either. Just mist the cubes and the plants once or twice a day. The stems need to callous over to form roots, so it needs air as much as water

 

[Purple love]

I found with the root riot cubes it was best to soak them in a weak veg solution .... but after trying loads of times and not having a very high percentage I bought an aero cloner and I'm around 90 percent success with one of these simply snip the cut prune the leaves set it and forget it .. best piece of kit I've ever bought

send me a link please thank you

 

[Purple love]

Raise them off the heat mat a bit with some bottle caps, or a few rings from a Mason jar lid. Some of those heat mats just keep on running. Make sure the vents on the dome are open. The light built into the dome along with the heat mat are roasting your clones. Mine root just fine using the side wash from my veg lights, which are actually underneath my dome.
View attachment 5340558
Don't let them sit in water either. Just mist the cubes and the plants once or twice a day. The stems need to callous over to form roots, so it needs air as much as water

thanks i had them like that and change it up i will go back to this thanks

 

[Liamp1603]

send me a link please thank you

X-Stream Aeroponic Propagator 12 20 40 Site Hydroponic Propagation | eBay

PRODUCT INFORMATION.

www.ebay.co.uk

 

[Purple love]

th

X-Stream Aeroponic Propagator 12 20 40 Site Hydroponic Propagation | eBay

PRODUCT INFORMATION.

www.ebay.co.uk

thanks

 

[Richard Drysift]

Two words: Clone King

 

[Purple love]

Those should be moist and covered with a dome. The ridiculously dry cubes and low humidity don't seem to be working too well.

They are cover with plenty of humidity this is a picture with the dome off