meanwell drivers

I am planning on building an Led array using 12 Bridgelux EB Gen 2 strips (BXEB-L1120Z-35E4000-C-B3). I would wire split them into groups of 3, wiring them in parallel and then wiring the 4 of them in series. The driver used will be a Meanwell HLG-480H-C2800B. This would give each strip 39v...

Sorry if this has been answered but have looked through threads and can’t find answer to my specific question. I have purchased 4x qb 648 boards from HLG along with two Slate 2 triple heat sinks(or XL heat sinks) with one board on each end of the XLheat sinks. I have not bought purchased...

So I ordered a kit 250 watt 5 cree cxb 3590s and it came with a meanwell HLG240H-C1400B. Works great.... I ordered another what I thought was the same kit but the driver this time is a HLG320H-C1400B, same COBS and all... if I hook this up and it goes to full power will this push too much to my...

Hey all I'm in dire need of some help understanding a light im wanting to buy. Looking for someone that knows there stuff regarding cob setups. Ive been wanting to run a cob setup for a long time and I finally found a great deal on one but I don't understand why its so different from most others...

Okay so I know amazon has cheap and crappy leds which should be avoided like incurable VD! That being said I have read great things about timber, rapidled and few other brands. I’m not afraid of dyi kits This is what I’m looking at...

I am having trouble with my Vero 29Se setup, and I'm baffled! (skip to "The Problem" below if you are just looking for a short question :P) Vero29 Cobs , HLG Meanwell Drivers , Cased Potentiometer Knob (It was ordered as a set, so the parts should all be adequately matching..i.e. the drivers...

Hello people, Been thinking about Switching over to COB LED's from my 250w HPS, in my 60cm X 60cm (2ftX2ft) flowering tent for a couple of weeks now. I'm not running Co2 so was going to try aim for the 1000/1200 PPFD range. The reason for the swap is duo to high temps forcing me to run my fan...

Hello everyone first post long time lurker lol. I am looking to upgrade from my mars 300w (135 actual) to a cob setup for my 2×2×4 tent. I have been thinking about running 4 maybe 5 Vero 29 gen 7 d series chips (3000k) on a mean Well hlg 185h-1050b driver. To my understanding the fv of the d...

Hi guys, I ´m not new here but mostly I found everything I need without questioning but now I´m stuck at the point. I´m building my own LED COB and I ´m not sure how to properly connect meanwell driver with led cobs and potentiometer? I ´m going wire them in series. Maybe if you can draw me...

Need Advice on choice of led driver , building a 2 lamp cob array Citizen CLU048-1212 in series but will running a mean well ELG-100-C1400A will it be better than the ELG-150-C1400A ? I am ok with math but not great. Also Please tell me if I am posting in wrong place!! Thanks in advance TJ

Hello to everybody, i'm going to buy a MeanWell HLG-320H-C1400 to drive 5 CLU 048. I'd like to buy the B version instead the A because i think the internal screw is not so practical in current use. Could somebody help me to find the right Potentiometer to buy (1-10 V? 0-10V) maybe linking me...

Hi, could you please help me to understand which is the best MW driver for 200-250W DIY cob led? I will use an arctic64 active heatsink(alpine 11 seems to be small) so 25°C may be not utopy. VERO29D need 37.2V at 1.4A 36.5V at 1050mA and 38.7V at 2.1A I' ve a 70x70CM grow box (2.3 ft) so i...

Dear DIY Vets, Please run a rough scan of my parts list and let me know if you see any red flags, pretty please.... First time build: If someone could take a look and see if I am missing any parts for this build, please let me know. Thanks so much. (10) Cree CXB 3590s CD bin 36v Angled...

i am building a 4x12 led room it will be separated into 4 4x4 chambers I have 8 cree cxa 3070 and 3 vero 29s the vero 29s are being ran by a meanwell 185 c1400b driver on a 16 inch heatsink active cooled I plan on having the 8 cree cxa 3070s mounted on 2 36 inch heatsinks I am not sure on driver...

I'm planning to drive 4x Samsung inFlux 02 hardstrips on a 2ft x 5" heatsink with a Meanwell LPV-60-48. Does anyone know if this will actually work or am I wasting my time on a bad driver configuration? Thanks!