new vero 29 gen 7 driver questions

Both Drivers Are On I Will Post Pics And Temps In 4 hours

alesh said:

Interesting
It'd awesome if you could also measure P_in and P_out of both drivers.

Click to expand...

Sorry Brother But That's Not An Easy Task. Both Driver Cords Are Triple Protected By Marine Heat Shrink

in absence of power ,measurements can you tell us what the loads on each one are?

what would be your suggestion if i were only be able to use 110 vac to power the drivers.

The Dawg said:

4 Vero 29'S 4000K On An Inventronics 320-2100 mA Will Rock Your World

Click to expand...

CobKits said:

in absence of power ,measurements can you tell us what the loads on each one are?

Click to expand...

Yes 320 watts 2.67 amps both will be pictured.

Mystuda said:

what would be your suggestion if i were only be able to use 110 vac to power the drivers.

Click to expand...

Its The Same Driver

1st Set Is The Inventronics 320-2100


This Set Is The Hlg 320-2100 As You Can See I Have It Elevated

That Was Weird Here's The Wattage for The Inventronics

are those both hooked up to cobs or no ? crazy about those temps

so inventronics = teabaggable
meanwell = not so much

meanwell=burnt sacz

sixstring2112 said:

are those both hooked up to cobs or no ? crazy about those temps

Click to expand...

Yes And Get This The Heatsinks For the Inventronics Is A Artic 64. The Meanwell Sits Outside The Tent while The Inventronics Is Attached To The Bar Inside The Tent

oh ten 4,so theres a few variables at play here.maybe those artics are the shit afterall,or maybe a wire size or length difference is in play to? same type of cob i take it ?

im still keepin my sac clear of that meanwell haha

so wait are you saying the inventronics is using an arctic cooler as well?

sixstring2112 said:

or maybe a wire size or length difference is in play to?

Click to expand...

see voltage drop calculator at bottom
http://www.powerstream.com/Wire_Size.htm

not hard to drop a few percent or more of voltage with remote drivers

sixstring2112 said:

oh ten 4,so theres a few variables at play here.maybe those artics are the shit afterall,or maybe a wire size or length difference is in play to? same type of cob i take it ?

im still keepin my sac clear of that meanwell haha

Click to expand...

Yes The Are Always Variables. In This Case They Arnt In Favor Of The Inventronics. NO The Artics Are NOT The Shit Which Is Why I Only Ran Them For A Few Hours On High

CobKits said:

see voltage drop calculator at bottom
http://www.powerstream.com/Wire_Size.htm

not hard to drop a few percent or more of voltage with remote drivers

Click to expand...

Really Tisk Tisk Half Ass Reading Again I See Tisk Tisk. This Argument Has Been Made Before And Your Voltage Drop Chart Show's Very Little Voltage Drop Over A 1000 FEET. So I Think The Average Home Grower With The Few Feet That We Run Our Remote Drivers With Are Fairly Safe

well i was looking at that yesterday to determine voltage drop between 3 channels on remote drivers 12 feet away thru an 18/6 cable and im getting almost 2% voltage drop. which can be a deal killer when your cobs are near the top of your 48V driver... so in some cases yes it is important

say for example a citi 1818 which tops out a 48V 'A' driver at 53.5V or about 1700 mA.

2% drop on voltage and youre not getting over 1100 mA with that.

The Dawg said:

Really Tisk Tisk Half Ass Reading Again I See Tisk Tisk. This Argument Has Been Made Before And Your Voltage Drop Chart Show's Very Little Voltage Drop Over A 1000 FEET. So I Think The Average Home Grower With The Few Feet That We Run Our Remote Drivers With Are Fairly Safe

Click to expand...

anyway mean well recommends 150cm so i agree, this is a moot point