What did you accomplish today?

[DCcan]

I carry a lot of stuff . Water, first aid kit, toilet paper and plastic bags. Food, keys, phone .bear spray, pocket knife, since there are a lot of mountain lions where I live, I carry a 9mm In case it attacks me and brass knuckles in case I have to punch him in the mouth. Some hiking poles .

Pretty much the same for my day bag when you go to the boodocks plus a compass with declination.
The 1st aid bag is stuffed with tape, med tools, trauma bandages, coagulant gauze.
Schnapps, water filter and water tablets, mini umbrella is a lifesaver with a trashbag.

 

[StonedGardener]

I carry a lot of stuff . Water, first aid kit, toilet paper and plastic bags. Food, keys, phone .bear spray, pocket knife, since there are a lot of mountain lions where I live, I carry a 9mm In case it attacks me and brass knuckles in case I have to punch him in the mouth. Some hiking poles .

 

[hillbill]

My main animal concern when walking, is running into unfriendly dogs in a pack. Carry an Air Horn and pepper spray or Bear Spray at times. I’ve mostly lived in or close to small towns and been playing and hunting and hiking in woods forever and never had a problem with wild animals.
We have plenty of predators but If there were more Mountain Lions, I’d more likely carry a handgun.

 

[hillbill]

Planted 10/10 SleeSkunk f2 with tails after 40 hours in the Viva Towel Sauna. Mother leaned to narrow leaves and some lankiness. Good smelly and sticky old strain.
Got those knee bends done and dogs out, in and fed.
Vaping Bodhi Dread Bread.

 

[bursto]

this is gonna sound lame, cause you guys are talking about in the wild, but i remember i was taking the kids to the zoo, few years back and i started teasing the mountain lion through the massive glass window, like na na come get me blah blah,

it ignored me at first, but i kept going on here puss puss

then it walked up the back of its enclosure got a full run up, ran at full speed, bounced off a side wall, flew about 12-15 feet in the air and almost landed on my side of the glass window, but it just didnt make it, i shut the f up after that

 

[curious2garden]

I just ran across these little gems on Amazon.


So my painting now includes additional electrical USB service without those pesky charger cubes/blocks. I like progress, sometimes.

 

[Aeroknow]

I just ran across these little gems on Amazon.
View attachment 5248759

So my painting now includes additional electrical USB service without those pesky charger cubes/blocks. I like progress, sometimes.

Do you actually need 20amp receptacles? Replacing receptacles on a 20amp circuit?

 

[DarkWeb]

Do you actually need 20amp receptacles? Replacing receptacles on a 20amp circuit?

Weld anywhere

 

[Aeroknow]

Weld anywhere

In my shop, i ran 50amp circuits on both sides Which reminds me, i still need to bring in the 3-50lb co2 bottles I got and trade in towards a new welder. Still not sure if I wanna get a new mig and a buzz box or just one of those multi purpose welders.

 

[Pacoson71]

Check the A rating for the charge rate on the outlets 2.1A is about as low as you want for modern smartphones.

 

[DarkWeb]

In my shop, i ran 50amp circuits on both sides Which reminds me, i still need to bring in the 3-50lb co2 bottles I got and trade in towards a new welder. Still not sure if I wanna get a new mig and a buzz box or just one of those multi purpose welders.

All depends on what you want to weld.

 

[Aeroknow]

All depends on what you want to weld.

Well, I want both a mig and a stick welder. I like having both. On the job i mostly used stick but at home i use the mig allot more.
Leaning towards just getting a buzz box here soon. Then a mig later. I could’ve already used a buzz box here more than a few times.

 

[DCcan]

Check the A rating for the charge rate on the outlets 2.1A is about as low as you want for modern smartphones.

Those look like 5v3.6a total, so not too bad.
I'd look for USB-C ones also, those are becoming more common, better charging rates.

 

[Pacoson71]

Those look like 5v3.6a total, so not too bad.
I'd look for USB-C ones also, those are becoming more common, better charging rates.

USB-C is also the industry standard. Hard to find new gadgets using anything else. old tech still has them though.
I glad I can plug things in without looking at top or bottom first!

 

[DCcan]

USB-C is also the industry standard. Hard to find new gadgets using anything else. old tech still has them though.
I glad I can plug things in without looking at top or bottom first!

I just noticed that outlet has a usb c in the center, cool!

 

[Dr.Amber Trichome]

I can punch and stab in the eye in one swing.

 

[Hiphophippo]

I just ran across these little gems on Amazon.
View attachment 5248759

So my painting now includes additional electrical USB service without those pesky charger cubes/blocks. I like progress, sometimes.

I love these things I put them in my kitchen and my bedroom

 

[DarkWeb]

Well, I want both a mig and a stick welder. I like having both. On the job i mostly used stick but at home i use the mig allot more.
Leaning towards just getting a buzz box here soon. Then a mig later. I could’ve already used a buzz box here more than a few times.

I rarely stick weld any more. It's funny it feels like every few years I'll do it though. I still have this

I think I bought it even before welding school. The wacko neighbor down the street had some crazy project and couldn't weld for shit. He got frustrated and sold it to me for I think it was $150 lol it's the AC/DC one too. I was about 15 when I got it and it's been everywhere with me. I mostly tig, mig is a close second, but I doubt I'll ever get rid of that one. I've watched it fall off trucks a few times.....down a set of stairs lol

 

[Hiphophippo]

I’ve used these for years now. lift and go I use them at home at work they are great for all jobs unless it’s structural and need to exceed specified amp rating on the welder but they do tig and stick. I can’t get used to the peddle on the bigger tig welders and I don’t really like that new pulsing arc stuff. I don’t really mig anything anymore as mostly everything is stainless I work around now.

 

[Hiphophippo]

I think the one I posted is only a stick one but the 1200 series is both stick and tig you can get them either or or both.