first grow room help
- Thread starter pbc2
- Start date
Can you like make me a diagram on how to construct this and link the items I need to buy
justugh
Well-Known Member
i made that little rough
ok the first pic is looking at from the top down
the 2nd part it is on the side
u cut it 1 inch thick ....then a 2nd one .....this leave u a little peice that is the back of it ............the peices u use are the ones that are squares and have the screw guild
as for picking the one for u i can not do that i am not there to doudle check the fit
if this does not work i am pour teacher
ok the first pic is looking at from the top down
the 2nd part it is on the side
u cut it 1 inch thick ....then a 2nd one .....this leave u a little peice that is the back of it ............the peices u use are the ones that are squares and have the screw guild
as for picking the one for u i can not do that i am not there to doudle check the fit
if this does not work i am pour teacher
Attachments
justugh
Well-Known Member
oh
u put the fans in and make sure u know where the wires are under the mylar
take the square shaped cover and place it on the outside so it overtop/covering the fans....in the screw guilds u push a drill tho so u have lined up holes on the side with the mylar from there u add 4 screws tho the mylar side tho the wood to hold the square box to the wood (u have to adjust for the lenght of the screw tho the wood into the box and leave some room to add a screws from other side to hold on the carbon pad /faceplate
the carbon pad is just a filter used in watertanks to clean the water u can get it at petco .............u get it u take the faceplate lay it on top of the pad and cut to size......from there u push screws tho the face plate so they go into the carbon pad ......once u know where the holes are u have to make a slit from the hole to the edge of the pad (so it does not twist up when u tighen it on ) the slits go to the top/and the bottom not the sides...so if it is the top of the plate u make 2 slits to the top of the pad..and vise verse for the lower ones....very important or it twist up and u have to make a new pad
after that u place the pad on the square and tighen the it down and u are done.............when u notice the smell getting stronger u change the pads (u can not reuse them they must be throw out and a new one placed in )...............the side sealing can be done with paint ...silcone....wood putty.......JB weld ............i know it is tempting to use lead paint for the blocking factor do not ....u will go mad in several years like me ........u want a latex or a oil based one
then u paint the box what ever color u want ............................i have a side trick i am learning .....if u do it right u could hang a picture infront of it there by blocking the light and the site of it .....u just have to make sure u leave air channels .................like a false pic with a wall safe idea ....have not worked it out if i do will yell
u put the fans in and make sure u know where the wires are under the mylar
take the square shaped cover and place it on the outside so it overtop/covering the fans....in the screw guilds u push a drill tho so u have lined up holes on the side with the mylar from there u add 4 screws tho the mylar side tho the wood to hold the square box to the wood (u have to adjust for the lenght of the screw tho the wood into the box and leave some room to add a screws from other side to hold on the carbon pad /faceplate
the carbon pad is just a filter used in watertanks to clean the water u can get it at petco .............u get it u take the faceplate lay it on top of the pad and cut to size......from there u push screws tho the face plate so they go into the carbon pad ......once u know where the holes are u have to make a slit from the hole to the edge of the pad (so it does not twist up when u tighen it on ) the slits go to the top/and the bottom not the sides...so if it is the top of the plate u make 2 slits to the top of the pad..and vise verse for the lower ones....very important or it twist up and u have to make a new pad
after that u place the pad on the square and tighen the it down and u are done.............when u notice the smell getting stronger u change the pads (u can not reuse them they must be throw out and a new one placed in )...............the side sealing can be done with paint ...silcone....wood putty.......JB weld ............i know it is tempting to use lead paint for the blocking factor do not ....u will go mad in several years like me ........u want a latex or a oil based one
then u paint the box what ever color u want ............................i have a side trick i am learning .....if u do it right u could hang a picture infront of it there by blocking the light and the site of it .....u just have to make sure u leave air channels .................like a false pic with a wall safe idea ....have not worked it out if i do will yell
DONNYS
New Member
they go together like a ham sandwich
DONNYS
New Member
go get u a bowl or cone
DONNYS
New Member
damn if u closer i share my ice cream and cones we get really high eat ice cream
justugh
Well-Known Member
put it this way u will need to bring a credit card
odds are smoke will not be the only thing and i have no idea how shine would effect u so best to have bail method handy ......strait off the tap it is 140proof ......our founding fathers would be proud hemp drink and arms what more does a posting need
took me several months but i know a nice rum vanella blend hint of white oak 130proof mixes well with coke .....distil that stuff 6 times
odds are smoke will not be the only thing and i have no idea how shine would effect u so best to have bail method handy ......strait off the tap it is 140proof ......our founding fathers would be proud hemp drink and arms what more does a posting need
took me several months but i know a nice rum vanella blend hint of white oak 130proof mixes well with coke .....distil that stuff 6 times
DONNYS
New Member
u funny as fuck lol
make me laugh